LAN9211-ABZJ SMSC, LAN9211-ABZJ Datasheet - Page 62

• Manufacturer Part Number: LAN9211-ABZJ
• Description: IC ETHERNET CTLR SGL CHIP 56-QFN
• Manufacturer: SMSC
• Type: Single Chip MAC and PHY Controllerr

Specifications of LAN9211-ABZJ

• Controller Type: Ethernet Controller
• Interface: Serial EEPROM
• Voltage - Supply: 3.3V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 56-QFN
• Product: Ethernet Controllers
• Number Of Transceivers: 1
• Standard Supported: IEEE 802.3 or IEEE 802.3u
• Data Rate: 10 Mbps or 100 Mbps
• Supply Voltage (max): 5 V
• Supply Voltage (min): 3.3 V
• Supply Current (max): 86 mA
• Maximum Operating Temperature: + 70 C
• Ethernet Connection Type: 100BASE-TX or 10BASE-T
• Minimum Operating Temperature: 0 C
• Mounting Style: SMD/SMT
• No. Of Ports: 2
• Ethernet Type: IEEE 802.3 / 802.3u
• Interface Type: HBI
• Supply Current: 86mA
• Supply Voltage Range: 2.97V To 3.63V
• Operating Temperature Range: 0°C To +70°C
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Current - Supply: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 638-1049-6

Revision 2.7 (03-15-10)
3.13.1.1
3.13.1.2
Receive Data FIFO Fast Forward
The RX data path implements an automatic data discard function. Using the RX data FIFO Fast
Forward bit (RX_FFWD) in the RX_DP_CTRL register, the host can instruct the LAN9211 to skip the
packet at the head of the RX data FIFO. The RX data FIFO pointers are automatically incremented to
the beginning of the next RX packet.
When performing a fast-forward, there must be at least 4 DWORDs of data in the RX data FIFO for
the packet being discarded. For less than 4 DWORDs do not use RX_FFWD. In this case data must
be read from the RX data FIFO and discarded using standard PIO read operations.
After initiating a fast-forward operation, do not perform any reads of the RX data FIFO until the
RX_FFWD bit is cleared. Other resources can be accessed during this time (i.e., any registers and/or
the other three FIFOs). Also note that the RX_FFWD will only fast-forward the RX data FIFO, not the
RX status FIFO.
The receiver does not have to be stopped to perform a fast-forward operation.
Force Receiver Discard (Receiver Dump)
In addition to the Receive data Fast Forward feature, LAN9211 also implements a receiver "dump"
feature. This feature allows the host processor to flush the entire contents of the RX data and RX
status FIFOs. When activated, the read and write pointers for the RX data and status FIFOs will be
returned to their reset state. To perform a receiver dump, the LAN9211 receiver must be halted. Once
the receiver stop completion is confirmed, the RX_DUMP bit can be set in the RX_CFG register. The
RX_DUMP bit is cleared when the dump is complete. For more information on stopping the receiver,
please refer to
on the RX_DUMP bit, please refer to
page
85.
Section 3.13.4, "Stopping and Starting the Receiver," on page
DATASHEET
High-Performance Small Form Factor Single-Chip Ethernet Controller with HP Auto-MDIX Support
Section 5.3.7, "RX_CFG—Receive Configuration Register," on
62
65. For more information
SMSC LAN9211
Datasheet