LAN9211-ABZJ SMSC, LAN9211-ABZJ Datasheet - Page 137

• Manufacturer Part Number: LAN9211-ABZJ
• Description: IC ETHERNET CTLR SGL CHIP 56-QFN
• Manufacturer: SMSC
• Type: Single Chip MAC and PHY Controllerr

Specifications of LAN9211-ABZJ

• Controller Type: Ethernet Controller
• Interface: Serial EEPROM
• Voltage - Supply: 3.3V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 56-QFN
• Product: Ethernet Controllers
• Number Of Transceivers: 1
• Standard Supported: IEEE 802.3 or IEEE 802.3u
• Data Rate: 10 Mbps or 100 Mbps
• Supply Voltage (max): 5 V
• Supply Voltage (min): 3.3 V
• Supply Current (max): 86 mA
• Maximum Operating Temperature: + 70 C
• Ethernet Connection Type: 100BASE-TX or 10BASE-T
• Minimum Operating Temperature: 0 C
• Mounting Style: SMD/SMT
• No. Of Ports: 2
• Ethernet Type: IEEE 802.3 / 802.3u
• Interface Type: HBI
• Supply Current: 86mA
• Supply Voltage Range: 2.97V To 3.63V
• Operating Temperature Range: 0°C To +70°C
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Current - Supply: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 638-1049-6

High-Performance Small Form Factor Single-Chip Ethernet Controller with HP Auto-MDIX Support
Datasheet
Chapter 7 Operational Characteristics
SMSC LAN9211
7.1
7.2
Supply Voltage (VDD_A33, VDD_IO)
Positive voltage on signal pins, with respect to ground
Negative voltage on signal pins, with respect to ground
Positive voltage on XTAL1/CLKIN, with respect to ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +4.6V
Positive voltage on XTAL2, with respect to ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +2.5V
Ambient Operating Temperature in Still Air (T
Storage Temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-65
Lead Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Refer to JEDEC Spec. J-STD-020
HBM ESD Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..+/- 5kV
Note 7.1
Note 7.2
Note 7.3
*Stresses exceeding those listed in this section could cause permanent damage to the device. This is
a stress rating only. Exposure to absolute maximum rating conditions for extended periods may affect
device reliability. Functional operation of the device at any condition exceeding those indicated in
Section 7.2, "Operating
applicable section of this specification is not implied.
Supply Voltage (VDD_A33, VDD_IO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +3.3V +/- 10%
Ambient Operating Temperature in Still Air (T
Note: Do not drive input signals without power supplied to the device.
Note: Apply and remove power to all power supply pins simultaneously, including the Ethernet
**Proper operation of the LAN9211 is guaranteed only within the ranges specified in this section.
Absolute Maximum Ratings*
Operating Conditions**
magnetics. Do not apply power to individual supply pins without the others.
When powering this device from laboratory or system power supplies, it is important that
the absolute maximum ratings not be exceeded or device failure can result. Some power
supplies exhibit voltage spikes on their outputs when AC power is switched on or off. In
addition, voltage transients on the AC power line may appear on the DC output. If this
possibility exists, it is suggested that a clamp circuit be used.
This rating does not apply to the following pins: XTAL1/CLKIN, XTAL2, EXRES1.
This rating does not apply to the following pins: EXRES1.
Conditions**",
DATASHEET
(Note
Section 7.6, "DC Electrical
137
7.1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0V to +3.3V+10%
A
A
). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0
). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0
(Note
(Note
7.2) . . . . . . . . . . . . . . . . . . . . . . . . . . +6V
7.3) . . . . . . . . . . . . . . . . . . . . . . . . -0.5V
Specifications", or any other
Revision 2.7 (03-15-10)
o
C to +150
o
o
C to +70
C to +70
o
o
o
C
C
C