MPC8308VMAGD Freescale Semiconductor, MPC8308VMAGD Datasheet - Page 83
![MPU POWERQUICC II PRO 473MAPBGA](/photos/6/76/67676/mpc8308_sml.jpg)
MPC8308VMAGD
Manufacturer Part Number
MPC8308VMAGD
Description
MPU POWERQUICC II PRO 473MAPBGA
Manufacturer
Freescale Semiconductor
Datasheets
1.MPC8308VMAGD.pdf
(90 pages)
2.MPC8308VMAGD.pdf
(2 pages)
3.MPC8308VMAGD.pdf
(1170 pages)
4.MPC8308VMAGD.pdf
(14 pages)
Specifications of MPC8308VMAGD
Processor Type
MPC83xx PowerQUICC II Pro 32-Bit
Speed
400MHz
Voltage
1V
Mounting Type
Surface Mount
Package / Case
473-MAPBGA
Product
Network Processor
Data Rate
256 bps
Frequency
400 MHz
Supply Voltage (max)
3.6 V
Supply Voltage (min)
3 V
Supply Current (max)
5 uA
Maximum Operating Temperature
+ 105 C
Minimum Operating Temperature
0 C
Interface
I2C, JTAG, SPI
Mounting Style
SMD/SMT
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Features
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MPC8308VMAGD
Manufacturer:
FREESCAL
Quantity:
300
Company:
Part Number:
MPC8308VMAGD
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Part Number:
MPC8308VMAGD
Manufacturer:
FREESCALE
Quantity:
20 000
Company:
Part Number:
MPC8308VMAGD400/266
Manufacturer:
FREESCAL
Quantity:
300
Company:
Part Number:
MPC8308VMAGDA
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
23.1
The device includes two PLLs.
23.2
Each of the PLLs listed above is provided with power through independent power supply pins (AV
core PLL and AV
preferably these voltages are derived directly from V
following.
There are a number of ways to reliably provide power to the PLLs, but the recommended solution is to
provide independent filter circuits as illustrated in
providing independent filters to each PLL the opportunity to cause noise injection from one PLL to the
other is reduced.
This circuit is intended to filter noise in the PLLs’ resonant frequency range from a 500 kHz to 10 MHz
range. It should be built with surface mount capacitors with minimum effective series inductance (ESL).
Consistent with the recommendations of Dr. Howard Johnson in High Speed Digital Design: A Handbook
of Black Magic (Prentice Hall, 1993), multiple small capacitors of equal value are recommended over a
single large value capacitor.
Each circuit should be placed as close as possible to the specific AV
noise coupled from nearby circuits. It should be possible to route directly from the capacitors to the AV
pin, which is on the periphery of package, without the inductance of vias.
Figure 54
23.3
Due to large address and data buses, and high operating frequencies, the device can generate transient
power surges and high frequency noise in its power supply, especially while driving large capacitive loads.
This noise must be prevented from reaching other components in the MPC8308 system, and the MPC8308
itself requires a clean, tightly regulated source of power. Therefore, it is recommended that the system
designer place at least one decoupling capacitor at each V
Freescale Semiconductor
1. The platform PLL generates the platform clock from the externally supplied SYS_CLK_IN input.
2. The e300 core PLL generates the core clock as a slave to the platform clock. The frequency ratio
The frequency ratio between the platform and SYS_CLK_IN is selected using the platform PLL
ratio configuration bits as described in
between the e300 core clock and the platform clock is selected using the e300 PLL ratio
configuration bits as described in
System Clocking
PLL Power Supply Filtering
Decoupling Recommendations
shows the PLL power supply filter circuits.
DD2
V
MPC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 2
DD
for the platform PLL). The AV
Figure 54. PLL Power Supply Filter Circuit
10 Ω
2.2 µF
Section 21.3, “Core PLL Configuration.”
Section 21.2, “System PLL Configuration.”
Figure
DD
DD
Low ESL Surface Mount Capacitors
level should always be equivalent to V
through a low pass filter scheme such as the
2.2 µF
DD
54, one to each of the two AV
, NV
DD
DD
AV
, GV
DD1
pin being supplied to minimize
DD
and AV
and LV
DD2
System Design Information
DD
pin of the device.
DD
pins. By
DD
DD1
, and
for
DD
83