EPF10K50EQI240-2 Altera, EPF10K50EQI240-2 Datasheet - Page 42
![IC FLEX 10KE FPGA 50K 240-PQFP](/photos/6/72/67260/544-240-pqfp_sml.jpg)
EPF10K50EQI240-2
Manufacturer Part Number
EPF10K50EQI240-2
Description
IC FLEX 10KE FPGA 50K 240-PQFP
Manufacturer
Altera
Series
FLEX-10KE®r
Datasheet
1.EPF10K30ETC144-3.pdf
(100 pages)
Specifications of EPF10K50EQI240-2
Number Of Logic Elements/cells
2880
Number Of Labs/clbs
360
Total Ram Bits
40960
Number Of I /o
189
Number Of Gates
199000
Voltage - Supply
2.3 V ~ 2.7 V
Mounting Type
Surface Mount
Operating Temperature
-40°C ~ 100°C
Package / Case
240-MQFP, 240-PQFP
Family Name
FLEX 10KE
Number Of Usable Gates
50000
Number Of Logic Blocks/elements
2880
# Registers
189
# I/os (max)
189
Frequency (max)
200MHz
Process Technology
CMOS
Operating Supply Voltage (typ)
2.5V
Logic Cells
2880
Ram Bits
40960
Device System Gates
199000
Operating Supply Voltage (min)
2.3V
Operating Supply Voltage (max)
2.7V
Operating Temp Range
-40C to 100C
Operating Temperature Classification
Industrial
Mounting
Surface Mount
Pin Count
240
Package Type
PQFP
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Other names
544-1945
EPF10K50EQI240-2
EPF10K50EQI240-2
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
EPF10K50EQI240-2
Manufacturer:
NEC
Quantity:
10
Company:
Part Number:
EPF10K50EQI240-2N
Manufacturer:
ALTERA22
Quantity:
209
FLEX 10KE Embedded Programmable Logic Devices Data Sheet
42
PCI Pull-Up Clamping Diode Option
FLEX 10KE devices have a pull-up clamping diode on every I/O,
dedicated input, and dedicated clock pin. PCI clamping diodes clamp the
signal to the V
Clamping diodes can also be used to limit overshoot in other systems.
Clamping diodes are controlled on a pin-by-pin basis. When V
3.3 V, a pin that has the clamping diode option turned on can be driven by
a 2.5-V or 3.3-V signal, but not a 5.0-V signal. When V
that has the clamping diode option turned on can be driven by a 2.5-V
signal, but not a 3.3-V or 5.0-V signal. Additionally, a clamping diode can
be activated for a subset of pins, which would allow a device to bridge
between a 3.3-V PCI bus and a 5.0-V device.
Slew-Rate Control
The output buffer in each IOE has an adjustable output slew rate that can
be configured for low-noise or high-speed performance. A slower slew
rate reduces system noise and adds a maximum delay of 4.3 ns. The fast
slew rate should be used for speed-critical outputs in systems that are
adequately protected against noise. Designers can specify the slew rate
pin-by-pin or assign a default slew rate to all pins on a device-wide basis.
The slow slew rate setting affects the falling edge of the output.
Open-Drain Output Option
FLEX 10KE devices provide an optional open-drain output (electrically
equivalent to open-collector output) for each I/O pin. This open-drain
output enables the device to provide system-level control signals (e.g.,
interrupt and write enable signals) that can be asserted by any of several
devices. It can also provide an additional wired-OR plane.
MultiVolt I/O Interface
The FLEX 10KE device architecture supports the MultiVolt I/O interface
feature, which allows FLEX 10KE devices in all packages to interface with
systems of differing supply voltages. These devices have one set of V
pins for internal operation and input buffers (VCCINT), and another set for
I/O output drivers (VCCIO).
CCIO
value and are required for 3.3-V PCI compliance.
CCIO
Altera Corporation
is 2.5 V, a pin
CCIO
is
CC