EPF6016TC144-3 Altera, EPF6016TC144-3 Datasheet - Page 28

• Manufacturer Part Number: EPF6016TC144-3
• Description: IC FLEX 6000 FPGA 16K 144-TQFP
• Manufacturer: Altera
• Series: FLEX 6000r

Specifications of EPF6016TC144-3

• Number Of Logic Elements/cells: 1320
• Number Of Labs/clbs: 132
• Number Of I /o: 117
• Number Of Gates: 16000
• Voltage - Supply: 4.75 V ~ 5.25 V
• Mounting Type: Surface Mount
• Operating Temperature: 0°C ~ 85°C
• Package / Case: 144-TQFP, 144-VQFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Total Ram Bits: -
• Other names: 544-1282

FLEX 6000 Programmable Logic Device Family Data Sheet
IEEE Std.
1149.1 (JTAG)
Boundary-Scan
Support
28
SAMPLE/PRELOAD Allows a snapshot of the signals at the device pins to be captured and examined during
EXTEST
BYPASS
Table 8. FLEX 6000 JTAG Instructions
JTAG Instruction
normal device operation, and permits an initial data pattern to be output at the device pins.
Allows the external circuitry and board-level interconnections to be tested by forcing a test
pattern at the output pins and capturing test result at the input pins.
Places the 1-bit bypass register between the TDI and TDO pins, which allows the BST
data to pass synchronously through the selected device to adjacent devices during
normal device operation.
Open-drain output pins on 5.0-V or 3.3-V FLEX 6000 devices (with a pull-
up resistor to the 5.0-V supply) can drive 5.0-V CMOS input pins that
require a V
When the pin is inactive, the trace will be pulled up to 5.0 V by the resistor.
The open-drain pin will only drive low or tri-state; it will never drive high.
The rise time is dependent on the value of the pull-up resistor and load
impedance. The I
selecting a pull-up resistor.
Output pins on 5.0-V FLEX 6000 devices with V
a pull-up resistor to the 5.0-V supply) can also drive 5.0-V CMOS input
pins. In this case, the pull-up transistor will turn off when the pin voltage
exceeds 3.3 V. Therefore, the pin does not have to be open-drain.
Power Sequencing & Hot-Socketing
Because FLEX 6000 family devices can be used in a mixed-voltage
environment, they have been designed specifically to tolerate any possible
power-up sequence. The V
in any order.
Signals can be driven into 3.3-V FLEX 6000 devices before and during
power up without damaging the device. Additionally, FLEX 6000 devices
do not drive out during power up. Once operating conditions are reached,
FLEX 6000 devices operate as specified by the user.
All FLEX 6000 devices provide JTAG BST circuitry that comply with the
IEEE Std. 1149.1-1990 specification.
FLEX 6000 devices. JTAG BST can be performed before or after
configuration, but not during configuration (except when you disable
JTAG support in user mode).
1
See
Testing in Altera Devices)
circuitry.
IH
Application Note 39 (IEEE 1149.1 (JTAG) Boundary-Scan
of 3.5 V. When the open-drain pin is active, it will drive low.
OL
current specification should be considered when
CCIO
Description
and V
for more information on JTAG BST
Table 8
CCINT
power planes can be powered
shows JTAG instructions for
CCIO
= 3.3 V or 5.0 V (with
Altera Corporation