EP1C3T144C6N Altera, EP1C3T144C6N Datasheet - Page 77

• Manufacturer Part Number: EP1C3T144C6N
• Description: IC CYCLONE FPGA 2910 LE 144-TQFP
• Manufacturer: Altera
• Series: Cyclone®r

Specifications of EP1C3T144C6N

• Number Of Logic Elements/cells: 2910
• Number Of Labs/clbs: 291
• Total Ram Bits: 59904
• Number Of I /o: 104
• Voltage - Supply: 1.425 V ~ 1.575 V
• Mounting Type: Surface Mount
• Operating Temperature: 0°C ~ 85°C
• Package / Case: 144-TQFP, 144-VQFP
• Family Name: Cyclone®
• Number Of Logic Blocks/elements: 2910
• # I/os (max): 104
• Frequency (max): 405.2MHz
• Process Technology: 0.13um (CMOS)
• Operating Supply Voltage (typ): 1.5V
• Logic Cells: 2910
• Ram Bits: 59904
• Operating Supply Voltage (min): 1.425V
• Operating Supply Voltage (max): 1.575V
• Operating Temp Range: 0C to 85C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 144
• Package Type: TQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Number Of Gates: -
• Lead Free Status / Rohs Status: Compliant
• Other names: 544-1662

Altera Corporation
May 2008
Notes to
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(10) Pin pull-up resistance values will lower if an external source drives the pin higher than V
(11) Drive strength is programmable according to values in
(12) Overdrive is possible when a 1.5 V or 1.8 V and a 2.5 V or 3.3 V input signal feeds an input pin. Turn on “Allow
(13) The Cyclone LVDS interface requires a resistor network outside of the transmitter channels.
(14) Capacitance is sample-tested only. Capacitance is measured using time-domain reflections (TDR). Measurement
C
C
C
C
C
Table 4–16. Cyclone Device Capacitance
IO
LVDS
VREF
DPCLK
CLK
Symbol
Refer to the
Conditions beyond those listed in
operation at the absolute maximum ratings for extended periods of time may have adverse affects on the device.
Minimum DC input is –0.5 V. During transitions, the inputs may undershoot to –2.0 V or overshoot to 4.6 V for
input currents less than 100 mA and periods shorter than 20 ns.
Maximum V
All pins, including dedicated inputs, clock, I/O, and JTAG pins, may be driven before V
powered.
Typical values are for T
V
This value is specified for normal device operation. The value may vary during power-up. This applies for all
V
R
will be lower if an external source drives the pin higher than V
voltage overdrive” for LVTTL/LVCMOS input pins in the Assignments > Device > Device and Pin Options > Pin
Placement tab when a device has this I/O combination. However, higher leakage current is expected.
accuracy is within ±0.5 pF.
CONF
I
CCIO
= ground, no load, no toggling inputs.
Tables 4–1
settings (3.3, 2.5, 1.8, and 1.5 V).
is the measured value of internal pull-up resistance when the I/O pin is tied directly to GND. R
Operating Requirements for Altera Devices Data
CC
Input capacitance for user I/O pin
Input capacitance for dual-purpose LVDS/user I/O pin
Input capacitance for dual-purpose V
Input capacitance for dual-purpose
Input capacitance for CLK pin.
rise time is 100 ms, and V
through 4–16:
A
= 25° C, V
Table 4–1
CCINT
Parameter
CC
= 1.5 V, and V
must rise monotonically.
may cause permanent damage to a device. Additionally, device
Note (14)
DPCLK
R E F
Cyclone Architecture
CCIO
Sheet.
/user I/O pin.
= 1.5 V, 1.8 V, 2.5 V, and 3.3 V.
/user I/O pin.
C C I O
.
chapter in the Cyclone Device Handbook.
Typical
12.0
CCINT
4.0
4.7
4.4
4.7
Operating Conditions
CCIO
.
and V
CCIO
Preliminary
CONF
are
Unit
pF
pF
pF
pF
pF
value
4–7