ADSP-2196MKSTZ-160 Analog Devices Inc, ADSP-2196MKSTZ-160 Datasheet - Page 9

• Manufacturer Part Number: ADSP-2196MKSTZ-160
• Description: IC DSP CONTROLLER 16BIT 144-LQFP
• Manufacturer: Analog Devices Inc
• Series: ADSP-21xxr
• Type: Fixed Pointr

Specifications of ADSP-2196MKSTZ-160

• Interface: Host Interface, SPI, SSP, UART
• Clock Rate: 160MHz
• Non-volatile Memory: ROM (48 kB)
• On-chip Ram: 40kB
• Voltage - I/o: 3.30V
• Voltage - Core: 2.50V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 144-LQFP
• Device Core Size: 16b
• Format: Fixed Point
• Clock Freq (max): 160MHz
• Mips: 160
• Device Input Clock Speed: 160MHz
• Ram Size: 40KB
• Program Memory Size: 48KB
• Operating Supply Voltage (typ): 2.5/3.3V
• Operating Supply Voltage (min): 2.37V
• Operating Supply Voltage (max): 2.63/3.6V
• Operating Temp Range: 0C to 70C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 144
• Package Type: LQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Table 1. Interrupt Priorities/Addresses (Continued)
1
Table 2
peripheral interrupts. To assign the peripheral interrupts a
different priority, applications write the new priority to their
corresponding control bits (determined by their ID) in the
Interrupt Priority Control register. The peripheral inter-
rupt’s position in the IMASK and IRPTL register and its
vector address depend on its priority level, as shown in
Table
limited to 16 bits, any peripheral interrupts assigned a
priority level of 11 are aliased to the lowest priority bit
position (15) in these registers and share vector address
0x00 01E0.
Table 2. Peripheral Interrupts and Priority at Reset
REV. PrA
These interrupt vectors start at address 0x10000 when the DSP is in
“no-boot”, run-form-external memory mode.
September 2001
Interrupt
User Assigned Interrupt
User Assigned Interrupt
User Assigned Interrupt—
Lowest Priority
Interrupt
Slave DMA/Host Port Interface
SPORT0 Receive
SPORT0 Transmit
SPORT1 Receive
SPORT1 Transmit
SPORT2 Receive/SPI0
SPORT2 Transmit/SPI1
UART Receive
UART Transmit
Timer A
Timer B
Timer C
1. Because the IMASK and IRPTL registers are
shows the ID and priority at reset of each of the
This information applies to a product under development. Its characteristics and specifications are subject to change with-
out notice. Analog Devices assumes no obligation regarding future manufacturing unless otherwise agreed to in writing.
For current information contact Analog Devices at 800/262-5643
IMASK/
IRPTL
13
14
15
ID
0
1
2
3
4
5
6
7
8
9
10
11
Vector
Address
0x00 01A0
0x00 01C0
0x00 01E0
Reset
Priority
0
1
2
3
4
5
6
7
8
9
10
11
1
Table 2. Peripheral Interrupts and Priority at Reset
Interrupt routines can either be nested with higher priority
interrupts taking precedence or processed sequentially.
Interrupts can be masked or unmasked with the IMASK
register. Individual interrupt requests are logically ANDed
with the bits in IMASK; the highest priority unmasked
interrupt is then selected. The emulation, power-down, and
reset interrupts are nonmaskable with the IMASK register,
but software can use the DIS INT instruction to mask the
power-down interrupt.
The Interrupt Control (ICNTL) register controls interrupt
nesting and enables or disables interrupts globally. The gen-
eral-purpose Programmable Flag (PFx) pins can be
configured as outputs, can implement software interrupts,
and (as inputs) can implement hardware interrupts. Pro-
grammable Flag pin interrupts can be configured for
level-sensitive, single edge-sensitive, or dual edge-
sensitive operation.
Table 3. Interrupt Control (ICNTL) Register Bits
The IRPTL register is used to force and clear interrupts.
On-chip stacks preserve the processor status and are auto-
matically maintained during interrupt handling. To support
interrupt, loop, and subroutine nesting, the PC stack is
33 levels deep, the loop stack is eight levels deep, and the
status stack is 16 levels deep. To prevent stack overflow, the
Interrupt
Programmable Flag 0 (any PFx)
Programmable Flag 1 (any PFx)
Memory DMA port
Bit
0–3
4
5
6
7
8–9
10
11
12–15
Description
Reserved
Interrupt Nesting Enable
Global Interrupt Enable
Reserved
MAC-Biased Rounding Enable
Reserved
PC Stack Interrupt Enable
Loop Stack Interrupt Enable
Reserved
ID
12
13
14
ADSP-2196
Reset
Priority
11
11
11
9