ADMCF328BRZ Analog Devices Inc, ADMCF328BRZ Datasheet - Page 17

• Manufacturer Part Number: ADMCF328BRZ
• Manufacturer: Analog Devices Inc

Specifications of ADMCF328BRZ

• Operating Current: 123mA
• Operating Temperature Classification: Industrial
• Package Type: SOIC W
• Operating Supply Voltage (min): -0.3V
• Operating Supply Voltage (max): 7V
• Lead Free Status / Rohs Status: Compliant

16-BIT PWM TIMER
Parameter
Counter Resolution
Edge Resolution (Single Update Mode)
Edge Resolution (Double Update Mode)
Programmable Dead Time Range
Programmable Dead Time Increments
Programmable Pulse Deletion Range
Programmable Pulse Deletion Increments
PWM Frequency Range
PWMSYNC Pulsewidth (T
Gate Drive Chop Frequency Range
PWM Registers
The configuration of the PWM registers is described at the end
of the data sheet. The parameters of the PWM block are tabu-
lated in Table V.
ADC OVERVIEW
The ADC of the ADMCF328 is based upon the single slope
conversion technique. This approach offers an inherently
monotonic conversion process within the noise and stability of its
components, and there will be no missing codes.
Select
VAUX0
VAUX1
VAUX2
Calibration (V
The single slope technique has been adapted on the ADMCF328
for four channels that are simultaneously converted. Refer to
Figure 11 for the functional schematic of the ADC. Two of the
main inputs (V1 and V2) are directly connected as high imped-
ance voltage inputs. The third main input channel (I
a special design to monitor the voltage on a current-sensing
resistor whose voltage is always below (more negative than)
the power supply rail. The fourth channel has been configured
with a serially connected 4-to-1 multiplexer. Table VI shows the
multiplexer input selection codes. One of these auxiliary
multiplexed channels is used to calibrate the ramp against the
internal voltage reference (V
REV. A
Table VI. ADC Auxiliary Channel Selection
REF
)
Table V. Fundamental Characteristics of PWM Generation Unit of ADMCF328
MODECTRL (1)
ADCMUX1
REF
CRST
0
0
1
1
).
)
MODECTRL (0)
ADCMUX0
0
1
0
1
SENSE
) has
–17–
Comparing each ADC input to a reference ramp voltage and
timing the comparison of the two signals performs the conversion
process. The actual conversion point is the time point inter-
section of the input voltage and the ramp voltage (V
Figure 12. This time is converted to counts by the 12-bit ADC
Timer Block and is stored in the ADC registers. The ramp voltage
used to perform the conversion is generated by driving a fixed
current into an off-chip capacitor, where the capacitor voltage is
Following reset, V
the conversion process are initiated by the PWMSYNC pulse,
as shown in Figure 12. The width of the PWMSYNC pulse is
controlled by the PWMSYNCWT register and should be pro-
grammed according to Figure 13 to ensure complete resetting.
In order to compensate for IC process manufacturing tolerances
(and to adjust for capacitor tolerances), the current source of the
ADMCF328 is software programmable. The software setting of the
magnitude of the ICONST current generator is accomplished by
selecting one of eight steps over approximately 20% current range.
C
GND
EXTERNAL
CHARGING
CAP
ICONST
I
VAUX2
VAUX0
VAUX1
SENSE
V2
V1
Min
0
150
0.05
0.02
–5
V
C
Figure 11. ADC Overview
C
0.8
= 0 at t = 0. This reset and the start of
MUX
4–1
V
C
Typ
16
100
50
100
0
100
COMP
COMP
=
COMP
COMP
COMP
(
ICONST_TRIM<2:0>
I C
(CAP RESET)
)
×
V1L
V2L
V3L
VAUXL
PWMTRIP
t
Max
100
100
12.5
5
BLOCK
REGISTERS
12-BIT
TIMER
ADC
ADMCF328
VREF
ADC
PWMSYNC (CONVST)
CLK MODECTRL<7>
C
Unit
Bits
ns
ns
µs
ns
µs
ns
Hz
µs
MHz
) as shown in
ADC REGISTERS
ADC1
ADC2
ADC3
ADCAUX
MODECTRL<0..1>