IDT5T2010BBI IDT, Integrated Device Technology Inc, IDT5T2010BBI Datasheet - Page 13

• Manufacturer Part Number: IDT5T2010BBI
• Description: IC CLK DVR ZD PLL 2.5V 144-BGA
• Manufacturer: IDT, Integrated Device Technology Inc
• Series: TeraClock™r
• Type: PLL Clock Driverr

Specifications of IDT5T2010BBI

• Pll: Yes with Bypass
• Input: eHSTL, HSTL, LVPECL, LVTTL
• Output: eHSTL, HSTL, LVTTL
• Number Of Circuits: 1
• Ratio - Input:output: 2:10
• Differential - Input:output: Yes/No
• Frequency - Max: 250MHz
• Divider/multiplier: Yes/No
• Voltage - Supply: 2.3 V ~ 2.7 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 144-BGA
• Frequency-max: 250MHz
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: 5T2010BBI

NOTES:
1. These power consumption characteristics are for all the valid input interfaces and cover the worst case input and output interface combinations.
2. The termination resistors are excluded from these measurements.
3. If the differential input interface is used, the true input is held LOW and the complementary input is held HIGH.
4. FS = HIGH.
POWER SUPPLY CHARACTERISTICS FOR 2.5V LVTTL OUTPUTS
DIFFERENTIAL INPUT AC TEST CONDITIONS FOR 2.5V LVTTL
NOTES:
1. A nominal 2.5V peak-to-peak input pulse level is specified to allow consistent, repeatable results in an automatic test equipment (ATE) environment. This device meets the V
2. A nominal 1.25V crossing point level is specified to allow consistent, repeatable results in an automatic test equipment (ATE) environment. This device meets the V
3. In all cases, input waveform timing is marked at the differential cross-point of the input signals.
4. The input signal edge rate of 2.5V/ns or greater is to be maintained in the 20% to 80% range of the input waveform.
SINGLE-ENDED INPUT AC TEST CONDITIONS FOR 2.5V LVTTL
NOTES:
1. A nominal 1.25V timing measurement reference level is specified to allow constant, repeatable results in an automatic test equipment (ATE) environment.
2. The input signal edge rate of 2V/ns or greater is to be maintained in the 10% to 90% range of the input waveform.
IDT5T2010
2.5V ZERO DELAY PLL CLOCK DRIVER TERACLOCK
Symbol
Symbol
(AC) specification under actual use conditions.
under actual use conditions.
Symbol
I
I
I
I
t
t
I
DDQQ
I
DDDQ
V
V
V
DDPD
I
TOTQ
DDQ
DDD
R
V
V
R
TOT
V
DIF
THI
THI
, t
, t
IH
X
IL
F
F
Quiescent V
Quiescent V
Power Down Current
Dynamic V
Current per Output
Dynamic V
Current per Output
Total Power V
Total Power V
Parameter
Input Signal Swing
Differential Input Signal Crossing Point
Input Timing Measurement Reference Level
Input Signal Edge Rate
Parameter
Input HIGH Voltage
Input LOW Voltage
Input Timing Measurement Reference Level
Input Signal Edge Rate
DD
DDQ
Parameter
DD
DDQ
DD
DDQ
Power Supply
Power Supply Current
Power Supply
Power Supply Current
Supply Current
Supply Current
(1)
(4)
(2)
(4)
(4)
(3)
(3)
(2)
V
PLL_EN = HIGH, DS
FBF
V
PLL_EN = HIGH, DS
FBF
V
V
V
V
V
V
V
DDQ
DDQ
DD
DD
DD
DDQ
DDQ
DDQ
DDQ
(3)
(1)
[2:1]
[2:1]
= Max., PD = LOW, nSOE = LOW, PLL_EN = HIGH
= Max., V
= Max., V
= 2.5V., F
= 2.5V., F
= 2.5V., F
= 2.5V., F
= Max., REF = LOW, PD = HIGH, nSOE = LOW,
= Max., REF = LOW, PD = HIGH, nSOE = LOW,
= LH, Outputs enabled, All outputs unloaded
= LH, Outputs enabled, All outputs unloaded
Test Conditions
DDQ
DDQ
VCO
VCO
VCO
VCO
13
= Max., C
= Max., C
= 100MHz, C
= 250MHz, C
= 100MHz, C
= 250MHz, C
[1:0]
[1:0]
(2)
= MM, nF
= MM, nF
L
L
= 0pF
= 0pF
L
L
L
L
= 15pF
= 15pF
= 15pF
= 15pF
[2:1]
[2:1]
= LH,
= LH,
INDUSTRIAL TEMPERATURE RANGE
Crossing Point
Typ.
200
0.5
15
12
15
30
40
60
80
Value
Value
V
V
V
V
2.5
DD
DD
0
2
DD
DD
/2
/2
(1)
Max
120
300
25
50
25
40
60
90
3
Units
Units
X
V/ns
V/ns
V
V
V
V
V
V
specification
μA/MHz
μA/MHz
Unit
mA
mA
mA
mA
μA
DIF