SCD128410QCE Intel, SCD128410QCE Datasheet - Page 90
SCD128410QCE
Manufacturer Part Number
SCD128410QCE
Description
Manufacturer
Intel
Datasheet
1.SCD128410QCE.pdf
(176 pages)
Specifications of SCD128410QCE
Pin Count
100
Lead Free Status / RoHS Status
Not Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
SCD128410QCE
Manufacturer:
INTEL
Quantity:
20 000
- Current page: 90 of 176
- Download datasheet (3Mb)
CD1284 — IEEE 1284-Compatible Parallel Interface Controller
6.0
6.1
6.2
6.2.1
90
Programming
Overview
As shown in the register summary tables in
up of a large array of registers. These registers control all aspects of device behavior; some affect
overall chip operations, and others affect only one channel. Fortunately, most of the registers are
only modified once, during initialization, and rarely modified during normal operation. The
purpose of this chapter is to discuss these aspects, as well as the methods of interacting with the
CD1284 for channel-service needs.
Initialization
To properly power-up a CD1284, several procedures must be completed. These include device
initialization, programming global functions, and setting channel-specific parameters. In most
cases, initialization routines are executed once; during the overall system boot-up. The following
sections discuss these steps in detail (see
Device Reset
The procedures that perform chip reset are normally executed after a power-up, system-wide reset.
The hardware reset control signal, RESET* causes the CD1284 to perform its own internal
initialization. If desired, the driver software can issue a full chip reset before chip initialization
begins. To accomplish this, use the following steps (see
1. Wait for CCR (Channel Command register) to contain 0x00.
2. Set the CAR (Channel Access register) to one of the two serial channels (2 or 3).
3. Write hexadecimal 81 (x’81) to the Channel Command Register (CCR).
4. Wait for the firmware revision code to be written into the GFRCR.
The contents of the CCR must be ‘0’ before a command is issued. This is required to ensure
that any currently executing command has completed before the new one is started. Since this
is probably the first command being written to the CD1284 after power-on initialization, the
CCR is likely to be ‘0’, but it is recommended to always check the CCR before writing in a
new command.
This step is required when the parallel channel does not respond to any value written to the
CCR address (this register does not exist in the parallel channel).
This command causes the CD1284 to perform an all-channel and global reset. It causes the
internal RISC processor to begin execution from its power-up reset location. The results are
the same as if the RESET* input is activated. All internal interface registers are cleared, the
FIFOs are flushed, and all channels are disabled.
The full-chip reset command is a special-case CCR operation. Normally, the commands issued
to the CCR affect only the channel selected by the CAR. In this case, the setting of the CAR is
insignificant, but must be set to channel 2 or 3. Unlike other commands issued to the CCR, the
global reset command does not use the clearing of the CCR. Instead, the GFRCR indicates that
the command is complete (see below).
Figure 18 on page 92
Chapter
4.0, the CD1284 local CPU interface is made
Figure 18
for a flow-chart step outline).
for a flow-chart step outline):
Datasheet
Related parts for SCD128410QCE
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
IEEE 1284-Compatible Parallel Interface Controller with Two High-Speed Asynchronous Serial Ports
Manufacturer:
INTEL [Intel Corporation]
Datasheet:
Part Number:
Description:
(SCD12 - SCD16) SURFACE MOUNT SCHOTTKY BARRIER RECTIFIER
Manufacturer:
Zowie Technology Corporation
Datasheet:
Part Number:
Description:
Microprocessor: Intel Celeron M Processor 320 and Ultra Low Voltage Intel Celeron M Processor at 600MHz
Manufacturer:
Intel Corporation
Part Number:
Description:
Intel 82550 Fast Ethernet Multifunction PCI/CardBus Controller
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
Intel StrataFlash memory 32 Mbit. Access speed 120 ns
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
Intel StrataFlash memory 32 Mbit. Access speed 120 ns
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
Intel StrataFlash memory 64 Mbit. Access speed 150 ns
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
Intel StrataFlash memory 32 Mbit. Access speed 100 ns
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
DA28F640J5A-1505 Volt Intel StrataFlash Memory
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
5 Volt Intel StrataFlash?? Memory
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
5 Volt Intel StrataFlash?? Memory
Manufacturer:
Intel Corporation
Part Number:
Description:
Intel 6300ESB I/O Controller Hub
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
Intel 82801DB I/O Controller Hub (ICH4), Pb-Free SLI
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
Intel 82801FB I/O Controller Hub (ICH6)
Manufacturer:
Intel Corporation
Datasheet: