FDC37M707-MS Standard Microsystems (SMSC), FDC37M707-MS Datasheet - Page 71
![no-image](/images/manufacturer_photos/0/6/632/standard_microsystems__smsc__sml.jpg)
FDC37M707-MS
Manufacturer Part Number
FDC37M707-MS
Description
Manufacturer
Standard Microsystems (SMSC)
Datasheet
1.FDC37M707-MS.pdf
(194 pages)
Specifications of FDC37M707-MS
Pin Count
100
Lead Free Status / RoHS Status
Compliant
- Current page: 71 of 194
- Download datasheet (765Kb)
This bit controls the Request To Send (nRTS)
output.
manner identical to that described above for bit
0.
Bit 2
This bit controls the Output 1 (OUT1) bit. This
bit does not have an output pin and can only be
read or written by the CPU.
Bit 3
Output 2 (OUT2). This bit is used to enable an
UART interrupt. When OUT2 is a logic "0", the
serial port interrupt output is forced to a high
impedance state - disabled. When OUT2 is a
logic "1", the serial port interrupt outputs are
enabled.
Bit 4
This bit provides the loopback feature for
diagnostic testing of the Serial Port. When bit 4
is set to logic "1", the following occur:
1.
2.
3.
4.
5.
6.
7.
This feature allows the processor to verify the
transmit and receive data paths of the Serial
Port. In the diagnostic mode, the receiver and
the transmitter interrupts are fully operational.
The TXD is set to the Marking State(logic
"1").
The
disconnected.
The output of the Transmitter Shift Register
is "looped back" into the Receiver Shift
Register input.
All MODEM Control inputs (nCTS, nDSR,
nRI and nDCD) are disconnected.
The four MODEM Control outputs (nDTR,
nRTS, OUT1 and OUT2) are internally
connected to the four MODEM Control
inputs (nDSR, nCTS, RI, DCD).
The Modem Control output pins are forced
inactive high.
Data that is transmitted is immediately
received.
Bit 1 affects the nRTS output in a
receiver
Serial
Input
(RXD)
is
71
operational but the interrupts' sources are now
the lower four bits of the MODEM Control
Register instead of the MODEM Control inputs.
The interrupts are still controlled by the Interrupt
Enable Register.
Bits 5 through 7
These bits are permanently set to logic zero.
LINE STATUS REGISTER (LSR)
Address Offset = 5H, DLAB = X, READ/WRITE
Bit 0
Data Ready (DR).
whenever a complete incoming character has
been received and transferred into the Receiver
Buffer Register or the FIFO. Bit 0 is reset to a
logic "0" by reading all of the data in the Receive
Buffer Register or the FIFO.
Bit 1
Overrun Error (OE). Bit 1 indicates that data in
the Receiver Buffer Register was not read before
the next character was transferred into the
register,
character. In FIFO mode, an overrun error will
occur only when the FIFO is full and the next
character has been completely received in the
shift register, the character in the shift register is
overwritten but not transferred to the FIFO. The
OE indicator is set to a logic "1" immediately
upon detection of an overrun condition, and
reset whenever the Line Status Register is read.
Bit 2
Parity Error (PE).
received data character does not have the
correct even or odd parity, as selected by the
even parity select bit. The PE is set to a logic
"1" upon detection of a parity error and is reset
to a logic "0" whenever the Line Status Register
is read.
associated with the particular character in the
FIFO it applies to. This error is indicated when
the associated character is at the top of the
FIFO.
thereby
In the FIFO mode this error is
destroying
Bit 2 indicates that the
It is set to a logic "1"
the
previous
Related parts for FDC37M707-MS
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![LAN91C111-NU](/photos/31/30/313086/406-128-tqfp_tmb.jpg)
Part Number:
Description:
Manufacturer:
Standard Microsystems (SMSC)
Datasheet:
![LAN9115-MT](/images/manufacturer_photos/0/6/632/standard_microsystems__smsc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Standard Microsystems (SMSC)
Datasheet:
![LAN9118-MT](/images/manufacturer_photos/0/6/632/standard_microsystems__smsc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Standard Microsystems (SMSC)
Datasheet:
![USB2229-NU-02](/images/manufacturer_photos/0/6/632/standard_microsystems__smsc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Standard Microsystems (SMSC)
Datasheet:
![USB2601-NU-05](/photos/31/30/313086/406-128-tqfp_tmb.jpg)
Part Number:
Description:
Manufacturer:
Standard Microsystems (SMSC)
Datasheet:
![USB2514B-AEZG](/images/manufacturer_photos/0/6/632/standard_microsystems__smsc__tmb.jpg)
Part Number:
Description:
USB CHIP
Manufacturer:
Standard Microsystems (SMSC)
Datasheet:
![USB2514BI-AEZG](/images/manufacturer_photos/0/6/632/standard_microsystems__smsc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Standard Microsystems (SMSC)
Datasheet:
![USB2251-NU-05](/images/manufacturer_photos/0/6/632/standard_microsystems__smsc__tmb.jpg)
Part Number:
Description:
ULTRA FAST USB 2.0 MULTI-SLOT FLASH MEDI
Manufacturer:
Standard Microsystems (SMSC)
Datasheet:
![LAN91C96-MS](/images/manufacturer_photos/0/6/632/standard_microsystems__smsc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Standard Microsystems (SMSC)
Datasheet:
![LAN9215-MT](/photos/31/30/313088/100pin_tqfp_tmb.jpg)
Part Number:
Description:
Manufacturer:
Standard Microsystems (SMSC)
Datasheet:
![LAN91C111I-NS](/images/manufacturer_photos/0/6/632/standard_microsystems__smsc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Standard Microsystems (SMSC)
Datasheet:
![USB2514I-HZH](/images/manufacturer_photos/0/6/632/standard_microsystems__smsc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Standard Microsystems (SMSC)
Datasheet:
![USB2514-HZH](/images/manufacturer_photos/0/6/632/standard_microsystems__smsc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Standard Microsystems (SMSC)
Datasheet:
![EMC2303-1-KP-TR](/images/manufacturer_photos/0/6/632/standard_microsystems__smsc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Standard Microsystems (SMSC)
Datasheet: