HSDL-3602-007 Lite-On Electronics, HSDL-3602-007 Datasheet - Page 6

• Manufacturer Part Number: HSDL-3602-007
• Description: Infrared Transceivers IR Transceiver 4.0Mb/s
• Manufacturer: Lite-On Electronics
• Type: TX/RXr
• Series: -r

Specifications of HSDL-3602-007

• Pulse Width: 1.6/4us
• Led Supply Voltage: -0.5 to 7V
• Dimensions: 12.2x4.9x4
• Peak Wavelength: 875/880nm
• Angle Of Half Sensitivity: 60/30°
• Communication Distance: 150
• Fall Time: 40/25ns
• Rise Time: 40/25ns
• Operating Supply Voltage (typ): 3.3V
• Operating Supply Voltage (min): 2.7V
• Operating Supply Voltage (max): 3.6V
• Mounting: Surface Mount
• Pin Count: 10
• Operating Temp Range: -20C to 70C
• Operating Temperature Classification: Commercial
• Data Rate: 3.90625Mbps
• Wavelength: 875 nm, 880 nm
• Continual Data Transmission: 4 Mbit/s
• Transmission Distance: 1.5 m
• Radiant Intensity: 250 mW/sr
• Half Intensity Angle Degrees: 30 deg to 60 deg
• Maximum Rise Time: 40 ns, 25 ns
• Maximum Fall Time: 40 ns, 25 ns
• Maximum Forward Current: 165 mA
• Operating Voltage: 2.7 V to 3.6 V
• Maximum Operating Temperature: + 70 C
• Minimum Operating Temperature: - 20 C
• Idle Current, Typ @ 25° C: 2.5mA
• Link Range, Low Power: 1m
• Operating Temperature: -20°C ~ 70°C
• Orientation: Side View
• Shutdown: Yes
• Size: 12.2mm x 4.9mm x 4mm
• Standards: IrPHY 1.4
• Supply Voltage: 2.7 V ~ 3.6 V
• Lead Free Status / RoHS Status: Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Compliant

6
Electrical & Optical Specifications
Specifications hold over the Recommended Operating Conditions unless otherwise noted. Unspecified test condi-
tions can be anywhere in their operating range. All typical values are at 25˚C and 3.3 V unless otherwise noted.
Parameter
Receiver
Receiver Data
Output Voltage
Logic High Receiver Input
Irradiance
Logic Low Receiver Input
Irradiance
Receiver Peak Sensitivity
Wavelength
Receiver SIR Pulse Width
Receiver MIR Pulse Width
Receiver FIR Pulse Width
Receiver ASK Pulse Width
Receiver Latency Time for FIR
Receiver Latency Time for SIR
Receiver Rise/Fall Times
Receiver Wake Up Time
Notes:
8. An in-band optical signal is a pulse/sequence where the peak wavelength, λp, is defined as 850 ≤ λp ≤ 900 nm, and the pulse characteristics are
9. Logic Low is a pulsed response. The condition is maintained for duration dependent on pattern and strength of the incident intensity.
10. For in-band signals ≤ 115.2 kb/s where 3.6 µW/cm
11. For in-band signals at 1.15 Mb/s where 9.0 µW/cm
12. For in-band signals of 125 ns pulse width, 4 Mb/s, 4 PPM at recommended 400 mA drive current.
13. Pulse width specified is the pulse width of the second 500 kHz carrier pulse received in a data bit. The first 500 kHz carrier pulse may exceed
14. The wake up time is the time between the transition from a shutdown state to an active state, and the time when the receiver is active and ready
compliant with the IrDA Serial Infrared Physical Layer Link Specification.
2 µs in width, which will not affect correct demodulation of the data stream. An ASK or DASK system using the HSDL-3602 has been shown to
correctly receive all data bits for 9 µW/cm
to receive infrared signals.
Logic Low
Logic High
Viewing
Angle
2
≤ EI ≤ 500 mW/cm
Symbol
V
V
2θ
EI
EI
λ
tpw (SIR) 1
tpw (MIR) 100
tpw (FIR) 85
tpw (ASK)
t
t
t
t
L
L
r/f
W
P
OL
OH
H
L
(FIR)
(SIR)
1/2
(RXD)
2
2
≤ EI ≤ 500 mW/cm
≤ EI ≤ 500 mW/cm
Min.
0
V
30
0.0036
0.0090
CC
2
– 0.2 —
incoming signal strength. ASK or DASK should use the FIR channel enabled.
2
2
.
.
Typ.
—
880
1
40
20
25
Max.
0.4
V
500
500
0.3
4.0
500
165
190
50
50
100
CC
Units
V
V
mW/cm
mW/cm
µW/cm
nm
µs
ns
ns
ns
µs
µs
µs
ns
µs
˚
2
2
2
Conditions
I
EI ≥ 3.6 µW/cm
θ
I
EI ≤ 0.3 µW/cm
θ
For in-band signals
≤ 115.2 kb/s
0.576 Mb/s ≤ in-band
signals ≤ 4 Mb/s
For in-band signals
θ
θ
θ
V
θ
V
500 kHz/50% duty cycle
carrier ASK
[14]
OL
OH
1/2
1/2
1/2
1/2
1/2
CC
1/2
CC
= 1.0 mA,
= –20 µA,
= 3 to 3.6 V
= 2.7 V
≤ 15˚
≤ 15˚
≤ 15˚
≤ 15˚
≤ 15˚
≤ 15˚
[10]
[11]
[12]
[12]
[13]
[8]
, C
, C
, C
, C
2
2
L
L
L
L
,
,
[8]
= 10 pF
= 10 pF
= 10 pF,
= 10 pF,
[8]