PIC24FJ64GA110-I/PT Microchip Technology, PIC24FJ64GA110-I/PT Datasheet - Page 176

• Manufacturer Part Number: PIC24FJ64GA110-I/PT
• Description: 16-bit, 16 MIPS, 64KB Flash, 16Kb RAM, 84 I/O, NanoWatt 100 TQFP 12x12x1mm TRAY
• Manufacturer: Microchip Technology
• Series: PIC® 24Fr

Specifications of PIC24FJ64GA110-I/PT

• Core Processor: PIC
• Core Size: 16-Bit
• Speed: 32MHz
• Connectivity: I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 85
• Program Memory Size: 64KB (22K x 24)
• Program Memory Type: FLASH
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 16x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-TQFP
• Processor Series: PIC24FJ256GA110
• Core: PIC
• Data Bus Width: 16 bit
• Data Ram Size: 16 KB
• Interface Type: UART, I2C, SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Timers: 5
• Operating Supply Voltage: 3.6 V
• Maximum Operating Temperature: - 40 C to + 85 C
• Mounting Style: SMD/SMT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

PIC24FJ256GA110 FAMILY
To set up the SPI module for the Standard Master mode
of operation:
1.
2.
3.
4.
5.
FIGURE 15-1:
DS39905E-page 176
SSx/FSYNCx
If using interrupts:
a)
b)
c)
Write the desired settings to the SPIxCON1 and
SPIxCON2 registers with the MSTEN bit
(SPIxCON1<5>) = 1.
Clear the SPIROV bit (SPIxSTAT<6>).
Enable SPI operation by setting the SPIEN bit
(SPIxSTAT<15>).
Write the data to be transmitted to the SPIxBUF
register. Transmission (and reception) will start
as soon as data is written to the SPIxBUF
register.
SDOx
SCKx
SDIx
Clear the SPIxIF bit in the respective IFSx
register.
Set the SPIxIE bit in the respective IECx
register.
Write the SPIxIP bits in the respective IPCx
register to set the interrupt priority.
Read SPIxBUF
Control
Sync
Transfer
SPIx MODULE BLOCK DIAGRAM (STANDARD MODE)
bit 0
SPIxBUF
SPIxSR
Control
Clock
Shift Control
Transfer
Write SPIxBUF
Select
Edge
To set up the SPI module for the Standard Slave mode
of operation:
1.
2.
3.
4.
5.
6.
7.
16
Clear the SPIxBUF register.
If using interrupts:
a)
b)
c)
Write the desired settings to the SPIxCON1
and SPIxCON2 registers with the MSTEN bit
(SPIxCON1<5>) = 0.
Clear the SMP bit.
If the CKE bit is set, then the SSEN bit
(SPIxCON1<8>) must be set to enable the SSx
pin.
Clear the SPIROV bit (SPIxSTAT<6>).
Enable SPI operation by setting the SPIEN bit
(SPIxSTAT<15>).
Secondary
Prescaler
1:1 to 1:8
Clear the SPIxIF bit in the respective IFSx
register.
Set the SPIxIE bit in the respective IECx
register.
Write the SPIxIP bits in the respective IPCx
register to set the interrupt priority.
Internal Data Bus
1:1/4/16/64
 2010 Microchip Technology Inc.
Prescaler
Primary
SPIxCON1<1:0>
SPIxCON1<4:2>
Enable
Master Clock
F
CY