PIC24FJ32GA104-I/PT Microchip Technology, PIC24FJ32GA104-I/PT Datasheet - Page 170

• Manufacturer Part Number: PIC24FJ32GA104-I/PT
• Description: 16-bit, 16 MIPS, 32KB Flash, 8KB RAM, Nanowatt XLP 44 TQFP 10x10x1mm TRAY
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 24Fr

Specifications of PIC24FJ32GA104-I/PT

• Core Processor: PIC
• Core Size: 16-Bit
• Speed: 32MHz
• Connectivity: I²C, IrDA, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 35
• Program Memory Size: 32KB (11K x 24)
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 13x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-TQFP, 44-VQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 876-1004 - PIC24 BREAKOUT BOARD
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

PIC24FJ64GA104 FAMILY
REGISTER 15-2:
DS39951C-page 170
bit 15
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 15-13
bit 12
bit 11
bit 10
bit 9
bit 8
bit 7
bit 6
bit 5
Note 1:
SSEN
R/W-0
U-0
—
2:
3:
4:
(4)
If DISSCK = 0, SCKx must be configured to an available RPn pin. See Section 10.4 “Peripheral Pin
Select (PPS)” for more information.
If DISSDO = 0, SDOx must be configured to an available RPn pin. See Section 10.4 “Peripheral Pin
Select (PPS)” for more information.
The CKE bit is not used in the Framed SPI modes. The user should program this bit to ‘0’ for the Framed
SPI modes (FRMEN = 1).
If SSEN = 1, SSx must be configured to an available RPn pin. See Section 10.4 “Peripheral Pin Select
(PPS)” for more information.
Unimplemented: Read as ‘0’
DISSCK: Disable SCKx pin bit (SPI Master modes only)
1 = Internal SPI clock is disabled; pin functions as I/O
0 = Internal SPI clock is enabled
DISSDO: Disable SDOx pin bit
1 = SDOx pin is not used by module; pin functions as I/O
0 = SDOx pin is controlled by the module
MODE16: Word/Byte Communication Select bit
1 = Communication is word-wide (16 bits)
0 = Communication is byte-wide (8 bits)
SMP: SPIx Data Input Sample Phase bit
Master mode:
1 = Input data is sampled at the end of data output time
0 = Input data is sampled at the middle of data output time
Slave mode:
SMP must be cleared when SPIx is used in Slave mode.
CKE: SPIx Clock Edge Select bit
1 = Serial output data changes on transition from active clock state to Idle clock state (see bit 6)
0 = Serial output data changes on transition from Idle clock state to active clock state (see bit 6)
SSEN: Slave Select Enable (Slave mode) bit
1 = SSx pin is used for Slave mode
0 = SSx pin is not used by module; pin is controlled by port function
CKP: Clock Polarity Select bit
1 = Idle state for clock is a high level; active state is a low level
0 = Idle state for clock is a low level; active state is a high level
MSTEN: Master Mode Enable bit
1 = Master mode
0 = Slave mode
R/W-0
CKP
U-0
—
SPI
X
CON1: SPIx CONTROL REGISTER 1
W = Writable bit
‘1’ = Bit is set
MSTEN
R/W-0
U-0
—
DISSCK
(2)
SPRE2
R/W-0
R/W-0
(3)
(1)
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
(4)
DISSDO
SPRE1
R/W-0
R/W-0
(2)
(1)
MODE16
SPRE0
R/W-0
R/W-0
 2010 Microchip Technology Inc.
x = Bit is unknown
PPRE1
R/W-0
R/W-0
SMP
PPRE0
CKE
R/W-0
R/W-0
(3)
bit 8
bit 0