PIC18F87K90T-I/PT Microchip Technology, PIC18F87K90T-I/PT Datasheet - Page 189

• Manufacturer Part Number: PIC18F87K90T-I/PT
• Description: 128kB Flash, 4kB RAM, 1kB EE, 16MIPS, NanoWatt XLP, LCD, 5V 80 TQFP 12x12x1mm T/
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F87K90T-I/PT

• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Program Memory Type: Flash
• Program Memory Size: 128 KB
• Data Ram Size: 4 KB
• Interface Type: I2C, SPI
• Maximum Clock Frequency: 64 MHz
• Number Of Timers: 11
• Operating Supply Voltage: 1.8 V to 5.5 V
• Maximum Operating Temperature: + 125 C
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12 bit, 24 Channel
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 64MHz
• Connectivity: I²C, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LCD, POR, PWM, WDT
• Number Of I /o: 69
• Eeprom Size: 1K x 8
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 24x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 80-TQFP
• Lead Free Status / Rohs Status: Details

13.2
The Timer1 module is an 8 or 16-bit incrementing
counter that is accessed through the TMR1H:TMR1L
register pair.
When used with an internal clock source, the module is
a timer and increments on every instruction cycle.
When used with an external clock source, the module
can be used as either a timer or counter. It increments
on every selected edge of the external source.
Timer1 is enabled by configuring the TMR1ON and
TMR1GE bits in the T1CON and T1GCON registers,
respectively.
When SOSC is selected as a Crystal mode (by
SOSCEL), the RC1/SOSCI/ECCP2/P2A/SEG32 and
RC0/SOSCO/SCLKI pins become inputs. This means
the values of TRISC<1:0> are ignored and the pins are
read as ‘0’.
13.3
The TMR1CS<1:0> and SOSCEN bits of the T1CON
register are used to select the clock source for Timer1.
Register 13-1
13.3.1
When the internal clock source is selected, the
TMR1H:TMR1L register pair will increment on multiples
of F
TABLE 13-1:
 2009-2011 Microchip Technology Inc.
OSC
TMR1CS1
, as determined by the Timer1 prescaler.
Timer1 Operation
Clock Source Selection
0
0
1
1
INTERNAL CLOCK SOURCE
displays the clock source selections.
TIMER1 CLOCK SOURCE SELECTION
TMR1CS0
1
0
0
0
SOSCEN
x
x
0
1
PIC18F87K90 FAMILY
Clock Source (F
Instruction Clock (F
External Clock on T1CKI Pin
Oscillator Circuit on SOSCI/SOSCO Pins
13.3.2
When the external clock source is selected, the Timer1
module may work as a timer or a counter.
When enabled to count, Timer1 is incremented on the
rising edge of the external clock input, T1CKI. Either of
these external clock sources can be synchronized to the
microcontroller
asynchronously.
When used as a timer with a clock oscillator, an
external, 32.768 kHz crystal can be used in conjunction
with the dedicated internal oscillator circuit.
Note:
EXTERNAL CLOCK SOURCE
In Counter mode, a falling edge must be
registered by the counter prior to the first
incrementing rising edge after any one or
more of the following conditions:
• Timer1 is enabled after a POR Reset
• Write to TMR1H or TMR1L
• Timer1 is disabled
• Timer1 is disabled (TMR1ON = 0)
When T1CKI is high, Timer1 is enabled
(TMR1ON = 1) when T1CKI is low.
OSC
system
OSC
Clock Source
)
/4)
clock
or
DS39957D-page 189
they
can
run