PIC12LF1840-I/MF Microchip Technology, PIC12LF1840-I/MF Datasheet - Page 214
![7 KB Flash, 256 Bytes RAM, 32 MHz Int. Osc, 6 I/0, Enhanced Mid Range Core, Nano](/photos/16/0/160077/dfn8_sml.jpg)
PIC12LF1840-I/MF
Manufacturer Part Number
PIC12LF1840-I/MF
Description
7 KB Flash, 256 Bytes RAM, 32 MHz Int. Osc, 6 I/0, Enhanced Mid Range Core, Nano
Manufacturer
Microchip Technology
Datasheet
1.PIC12F1840-IP.pdf
(382 pages)
Specifications of PIC12LF1840-I/MF
Processor Series
PIC12F
Core
PIC
Program Memory Type
Flash
Program Memory Size
7 KB
Data Ram Size
256 B
Interface Type
MI2C, SPI, EUSART
Number Of Timers
3
Operating Supply Voltage
1.8 V to 5.5 V
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
Package / Case
DFN-8
Development Tools By Supplier
MPLAB IDE Software
Minimum Operating Temperature
- 40 C
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PIC12LF1840-I/MF
Manufacturer:
MICROCHIP
Quantity:
887
- Current page: 214 of 382
- Download datasheet (4Mb)
PIC12(L)F1840
25.2
The Serial Peripheral Interface (SPI) bus is a
synchronous serial data communication bus that
operates in Full Duplex mode. Devices communicate in
a master/slave environment where the master device
initiates the communication. A slave device is
controlled through a chip select known as Slave Select.
The SPI bus specifies four signal connections:
• Serial Clock (SCK)
• Serial Data Out (SDO)
• Serial Data In (SDI)
• Slave Select (SS)
Figure 25-1
module when operating in SPI Mode.
The SPI bus operates with a single master device and
one or more slave devices. When multiple slave
devices are used, an independent Slave Select con-
nection is required from the master device to each
slave device.
Figure 25-4
master device and multiple slave devices.
The master selects only one slave at a time. Most slave
devices have tri-state outputs so their output signal
appears disconnected from the bus when they are not
selected.
Transmissions involve two shift registers, eight bits in
size, one in the master and one in the slave. With either
the master or the slave device, data is always shifted
out one bit at a time, with the Most Significant bit (MSb)
shifted out first. At the same time, a new Least
Significant bit (LSb) is shifted into the same register.
Figure 25-5
processors configured as master and slave devices.
Data is shifted out of both shift registers on the pro-
grammed clock edge and latched on the opposite edge
of the clock.
The master device transmits information out on its SDO
output pin which is connected to, and received by, the
slave’s SDI input pin. The slave device transmits infor-
mation out on its SDO output pin, which is connected
to, and received by, the master’s SDI input pin.
To begin communication, the master device first sends
out the clock signal. Both the master and the slave
devices should be configured for the same clock polar-
ity.
The master device starts a transmission by sending out
the MSb from its shift register. The slave device reads
this bit from that same line and saves it into the LSb
position of its shift register.
During each SPI clock cycle, a full duplex data
transmission occurs. This means that while the master
device is sending out the MSb from its shift register (on
its SDO pin) and the slave device is reading this bit and
DS41441B-page 214
SPI Mode Overview
shows the block diagram of the MSSP1
shows a typical connection between two
shows a typical connection between a
Preliminary
saving it as the LSb of its shift register, that the slave
device is also sending out the MSb from its shift register
(on its SDO pin) and the master device is reading this
bit and saving it as the LSb of its shift register.
After 8 bits have been shifted out, the master and slave
have exchanged register values.
If there is more data to exchange, the shift registers are
loaded with new data and the process repeats itself.
Whether the data is meaningful or not (dummy data),
depends on the application software. This leads to
three scenarios for data transmission:
• Master sends useful data and slave sends dummy
• Master sends useful data and slave sends useful
• Master sends dummy data and slave sends useful
Transmissions may involve any number of clock
cycles. When there is no more data to be transmitted,
the master stops sending the clock signal and it dese-
lects the slave.
Every slave device connected to the bus that has not
been selected through its slave select line must disre-
gard the clock and transmission signals and must not
transmit out any data of its own.
data.
data.
data.
2011 Microchip Technology Inc.
Related parts for PIC12LF1840-I/MF
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![TC1014-2.7VCT](/images/manufacturer_photos/0/4/440/microchip_technology_inc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet:
![TC1014-5.0VCT](/images/manufacturer_photos/0/4/440/microchip_technology_inc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet:
![TC1055-2.5VCT](/images/manufacturer_photos/0/4/440/microchip_technology_inc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet:
![TC1055-2.7VCT](/images/manufacturer_photos/0/4/440/microchip_technology_inc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet:
![TC1055-2.8VCT](/images/manufacturer_photos/0/4/440/microchip_technology_inc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet:
![TC1055-4.0VCT](/images/manufacturer_photos/0/4/440/microchip_technology_inc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet:
![TC1186-2.5VCT](/images/manufacturer_photos/0/4/440/microchip_technology_inc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet:
![TC1186-2.85VCT](/images/manufacturer_photos/0/4/440/microchip_technology_inc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet: