CPC5602CTR Clare, CPC5602CTR Datasheet - Page 9

• Manufacturer Part Number: CPC5602CTR
• Description: MOSFET N-CH 350V 5MA SOT-223
• Manufacturer: Clare
• Type: Power MOSFETr

Specifications of CPC5602CTR

• Fet Type: MOSFET N-Channel, Metal Oxide
• Fet Feature: Depletion Mode
• Rds On (max) @ Id, Vgs: 14 Ohm @ 50mA, 350mV
• Drain To Source Voltage (vdss): 350V
• Current - Continuous Drain (id) @ 25° C: 5mA
• Input Capacitance (ciss) @ Vds: 300pF @ 0V
• Power - Max: 2.5W
• Mounting Type: Surface Mount
• Package / Case: SOT-223 (3 leads + Tab), SC-73, TO-261
• Number Of Elements: 1
• Polarity: N
• Channel Mode: Depletion
• Drain-source On-res: 14Ohm
• Drain-source On-volt: 350V
• Continuous Drain Current: 5mA
• Power Dissipation: 2.5W
• Output Power (max): Not RequiredW
• Frequency (max): Not RequiredMHz
• Noise Figure: Not RequireddB
• Power Gain: Not RequireddB
• Drain Efficiency: Not Required%
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 3 +Tab
• Package Type: SOT-223
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Gate Charge (qg) @ Vgs: -
• Vgs(th) (max) @ Id: -
• Lead Free Status / Rohs Status: Compliant
• Other names: CLA298TR; CPC5602CTR

AT Command Set
Rev. 2
Command
&D
E
%E
&F
&G
Automatic Retrain
Options
Recall Factory
Profile
Guard Tone Options
Function and Description
Data Terminal &D determines how the modem responds to the DTR signal from the terminal. The country
Ready Options configuration may prevent the modem from detecting terminal DTR. In this case, the
modem assumes DTR is always on. In North America, terminal DTR is normally detected. If DTR detection
The response to changes in DTR also depends on the &Q and &D commands. This table defines what
happens when DTR goes off for all possible combinations of the &D and &Q commands. To see what
happens when DTR goes on refer to the &Q command. The default value is &D0 in North America:
&Q0
&Q1
A
B
C
D
Command Mode E tells the modem whether or not to echo characters sent from the terminal when the
modem is Character Echo accepting AT commands.
E0
E1
The %E command controls whether the modem will initiate retrain with the other modem during
a telephone line connection during operation in data modes supporting retrain. The modem always
responds to a retrain operation initiated by the remote modem. The modem can be forced to initiate a
retrain by the On-Line (O1) command.
%E0
%E1
&F changes these AT command options and S-registers to their default values. The default
values may be changed for use in different countries. The values for North America are:
S-registers
S0=0 S1=0
S6=2 S7=30
S12=50
Commands
B1
&G tells the modem which guard tone to transmit when the modem is transmitting the high band (i.e.,
answer handshake and answer mode).
&G0
&G1
&G2
has been prevented, the modem will respond with an ERROR result to this command.
E1
The modem hangs up the telephone line and issues an OK result code.
If in the On-Line state, the modem goes into the Command state and issues an OK result code.
The modem hangs up the telephone line and issues an OK result code. Auto-Answer is disabled as
long as DTR stays off.
The modem resets.
Does not echo characters sent from the terminal.
Echo characters sent from the terminal. This is the default value in North America.
Initiate a retrain if the datapump indicates one is required.
No guard tone. This is the default value in North America.
550 Hz guard tone (V.22 and V.22bis only)
1800 Hz guard tone (V.22 and V.22bis only)
Do not initiate a retrain.
M1
None
&D0
P
S17=10
A
S2=43
S8=2
Q0
www.clare.com
&D1
B
B
V1
S3=13
S25=5
S9=6
X4
&D2
C
C
&C0
S10=14
S4=10
S28=0
D3
&D0
D
D
S11=95
S29=25 S37=0
&G0
S5=8
&P0
&Q0
%E1
CPC2400E
9