CPC5602CTR Clare, CPC5602CTR Datasheet - Page 16

• Manufacturer Part Number: CPC5602CTR
• Description: MOSFET N-CH 350V 5MA SOT-223
• Manufacturer: Clare
• Type: Power MOSFETr

Specifications of CPC5602CTR

• Fet Type: MOSFET N-Channel, Metal Oxide
• Fet Feature: Depletion Mode
• Rds On (max) @ Id, Vgs: 14 Ohm @ 50mA, 350mV
• Drain To Source Voltage (vdss): 350V
• Current - Continuous Drain (id) @ 25° C: 5mA
• Input Capacitance (ciss) @ Vds: 300pF @ 0V
• Power - Max: 2.5W
• Mounting Type: Surface Mount
• Package / Case: SOT-223 (3 leads + Tab), SC-73, TO-261
• Number Of Elements: 1
• Polarity: N
• Channel Mode: Depletion
• Drain-source On-res: 14Ohm
• Drain-source On-volt: 350V
• Continuous Drain Current: 5mA
• Power Dissipation: 2.5W
• Output Power (max): Not RequiredW
• Frequency (max): Not RequiredMHz
• Noise Figure: Not RequireddB
• Power Gain: Not RequireddB
• Drain Efficiency: Not Required%
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 3 +Tab
• Package Type: SOT-223
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Gate Charge (qg) @ Vgs: -
• Vgs(th) (max) @ Id: -
• Lead Free Status / Rohs Status: Compliant
• Other names: CLA298TR; CPC5602CTR

CPC2400E
16
A result code is a line of text or a number the modem
sends to the terminal to indicate the result of a com-
mand execution. Some CONNECT result codes indi-
cate the telephone line data rate. The following table
provides a list of the available result codes.
Modem Result Codes
Number
0
1
2
3
4
5
6
7
8
10
16
17
20
21
Word
OK
CONNECT
RING
NO CARRIER
ERROR
CONNECT 1200
NO DIALTONE
BUSY
NO ANSWER
CONNECT 2400
CONNECT 1200/75
CONNECT 75/1200
BLACKLISTED
DELAYED
An invalid command was issued, or there was an error at any place in the command line.
Result Code Description
Command Line Executed without errors
The modem is in the On-line state, ready to transfer data.
The modem has detected a ring signal on the telephone line. The country configuration
may disable the modem’s ability to detect a telephone line ring signal.
No carrier signal was detected when answering or placing a telephone call, or carrier
was lost during a call. The modem also returns this response message when the tele
phone line connection is broken for any reason.
The modem is in the On-line state, ready to transfer data.
No dial tone was detected when the modem took the telephone line off hook.
The modem detected a busy signal on the telephone line.
Not enough silence was detected when the @ dial modifier was used.
The modem is in the On-line state, ready to transfer data. The telephone line data rate is
2400bps.
The modem is in the On-Line state, ready to transfer data. This modem transmits at
1200 bps and receives at 75 bps.
The modem is in the On-Line state, ready to transfer data. This modemtransmits at 75
bps and receives at 1200 bps.
The modem will not allow any number to be dialed until after the modem is reset.
The modem will not allow any number to be dialed now, but will allow dialing at some
future time.
www.clare.com
Rev. 2