DSPIC33EP512MU810-I/PT Microchip Technology, DSPIC33EP512MU810-I/PT Datasheet - Page 376

• Manufacturer Part Number: DSPIC33EP512MU810-I/PT
• Description: 100 PINS, 512KB Flash, 52KB RAM, 60 MHz, USB, 2xCAN, 15 DMA 100 TQFP 12x12x1mm T
• Manufacturer: Microchip Technology
• Series: dsPIC™ 33EPr

Specifications of DSPIC33EP512MU810-I/PT

• Embedded Interface Type: I2C, SPI, UART
• No. Of I/o's: 83
• Flash Memory Size: 536KB
• Supply Voltage Range: 3V To 3.6V
• Operating Temperature Range: -40°C To +85°C
• Digital Ic Case Style: TQFP
• No. Of Pins: 100
• Rohs Compliant: Yes
• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 60 MIPs
• Connectivity: CAN, I²C, IrDA, LIN, QEI, SPI, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, DMA, Motor Control PWM, POR, PWM, WDT
• Number Of I /o: 83
• Program Memory Size: 512KB (170K x 24)
• Program Memory Type: FLASH
• Eeprom Size: -
• Ram Size: 24K x 16
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 32x10b/12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-TQFP
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

dsPIC33EPXXXMU806/810/814 and PIC24EPXXXGU810/814
REGISTER 22-22: UxEPn: USB ENDPOINT n CONTROL REGISTERS (n = 0 TO 15)
DS70616E-page 376
bit 15
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 15-8
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
Note 1:
LSPD
R/W-0
U-0
—
(1)
These bits are available only for UxEP0, and only in Host mode. For all other UxEPn registers, these bits
are always unimplemented and read as ‘0’.
RETRYDIS
Unimplemented: Read as ‘0’
LSPD: Low-Speed Direct Connection Enable bit (UEP0 only)
1 = Direct connection to a low-speed device enabled
0 = Direct connection to a low-speed device disabled
RETRYDIS: Retry Disable bit (UEP0 only)
1 = Retry NAK transactions disabled
0 = Retry NAK transactions enabled; retry done in hardware
Unimplemented: Read as ‘0’
EPCONDIS: Bidirectional Endpoint Control bit
If EPTXEN and EPRXEN = 1:
1 = Disable Endpoint n from control transfers; only TX and RX transfers are allowed
0 = Enable Endpoint n for control (SETUP) transfers; TX and RX transfers are also allowed
For all other combinations of EPTXEN and EPRXEN:
This bit is ignored.
EPRXEN: Endpoint Receive Enable bit
1 = Endpoint n receive enabled
0 = Endpoint n receive disabled
EPTXEN: Endpoint Transmit Enable bit
1 = Endpoint n transmit enabled
0 = Endpoint n transmit disabled
EPSTALL: Endpoint Stall Status bit
1 = Endpoint n was stalled
0 = Endpoint n was not stalled
EPHSHK: Endpoint Handshake Enable bit
1 = Endpoint handshake enabled
0 = Endpoint handshake disabled (typically used for isochronous endpoints)
R/W-0
U-0
—
(1)
W = Writable bit
‘1’ = Bit is set
U-0
U-0
—
—
EPCONDIS
R/W-0
U-0
—
Preliminary
(1)
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
EPRXEN
R/W-0
U-0
—
(1)
EPTXEN
R/W-0
U-0
—
 2009-2011 Microchip Technology Inc.
x = Bit is unknown
EPSTALL
R/W-0
U-0
—
EPHSHK
R/W-0
U-0
—
bit 8
bit 0