ADUC7036CCPZ-RL Analog Devices Inc, ADUC7036CCPZ-RL Datasheet - Page 16

• Manufacturer Part Number: ADUC7036CCPZ-RL
• Description: Flash 96k ARM7 Dual 16-Bit ADC LIN I.C.
• Manufacturer: Analog Devices Inc
• Series: MicroConverter® ADuC7xxxr

Specifications of ADUC7036CCPZ-RL

• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 20.48MHz
• Connectivity: LIN, SPI, UART/USART
• Peripherals: PSM, Temp Sensor, WDT
• Number Of I /o: 9
• Program Memory Size: 96KB (96K x 8)
• Program Memory Type: FLASH
• Eeprom Size: -
• Ram Size: 6K x 8
• Voltage - Supply (vcc/vdd): 3.5 V ~ 18 V
• Data Converters: A/D 2x16b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 115°C
• Package / Case: 48-VFQFN Exposed Pad, CSP
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

ADuC7036
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
Table 7. Pin Function Descriptions
Pin No.
1
2
3
4
5
6
7
8, 34, 35
9, 16, 17,
23, 25, 26,
32, 38 to
40, 43, 45
10
Mnemonic
RESET
GPIO_5/IRQ1/RxD
GPIO_6/TxD
GPIO_7/IRQ4
GPIO_8/IRQ5
TCK
TDI
DGND
NC
TDO
Type
I
I/O
I/O
I/O
I/O
I
I
S
O
GPIO_5/IRQ1/RxD
NOTES
1. NC = NO CONNECT.
2. THE EXPOSED PAD SHOULD BE CONNECTED TO DGND.
GPIO_7/IRQ4
GPIO_8/IRQ5
GPIO_6/TxD
1
RESET
NTRST
DGND
Description
Reset Input Pin. Active low. This pin has an internal, weak pull-up resistor to REG_DVDD and
should be left unconnected when not in use. For added security and robustness, it is
recommended that this pin be strapped via a resistor to REG_DVDD.
General-Purpose Digital I/O 5/External Interrupt Request 1/Receive Data for UART Serial Port. By
default and after a power-on reset, this pin configures as an input. The pin has an internal, weak
pull-up resistor and should be left unconnected when not in use.
General-Purpose Digital I/O 6/Transmit Data for UART Serial Port. By default and after a power-
on reset, this pin configures as an input. The pin has an internal, weak pull-up resistor and
should be left unconnected when not in use.
General-Purpose Digital I/O 7/External Interrupt Request 4. By default and after a power-on
reset, this pin configures as an input. The pin has an internal, weak pull-up resistor and should
be left unconnected when not in use.
General-Purpose Digital I/O 8/External Interrupt Request 5. By default and after a power-on
reset, this pin configures as an input. The pin has an internal, weak pull-up resistor and should
be left unconnected when not in use.
JTAG Test Clock. This clock input pin is one of the standard 5-pin JTAG debug ports on the part.
TCK is an input pin only and has an internal, weak pull-up resistor. This pin is left unconnected
when not in use.
JTAG Test Data Input. This data input pin is one of the standard 5-pin JTAG debug ports on the
part. TDI is an input pin only and has an internal, weak pull-up resistor. This pin can be left
unconnected when not in use.
Ground Reference for On-Chip Digital Circuits.
No Connect. These pins are not internally connected and are reserved for possible future use.
Therefore, do not externally connect these pins. These pins can be grounded, if required.
JTAG Test Data Output. This data output pin is one of the standard 5-pin JTAG debug ports on
the part. TDO is an output pin only. At power-on, this output is disabled and pulled high via an
internal, weak pull-up resistor. This pin is left unconnected when not in use.
TDO
TMS
TCK
TDI
NC
10
12
11
1
2
3
4
5
6
7
8
9
PIN 1
INDICATOR
Figure 7. Pin Configuration
Rev. C | Page 16 of 132
ADuC7036
(Not to Scale)
TOP VIEW
36
35
34
33
32
31
30
29
28
27
26
25
XTAL1
DGND
DGND
REG_DVDD
NC
GPIO_4/ECLK
GPIO_3/MOSI
GPIO_2/MISO
GPIO_1/SCLK
GPIO_0/IRQ0/SS
NC
NC