T1611100 Red Lion Controls, T1611100 Datasheet - Page 15

• Manufacturer Part Number: T1611100
• Description: PID TEMPERATURE CONTROLLER, 3RELAYS
• Manufacturer: Red Lion Controls
• Type: Temperaturer

Specifications of T1611100

• Thermocouple Type: T, E, J, K, R, S, B, N, C, Linear MV
• Operating Temperature Max: 50°C
• Operating Temperature Min: 0°C
• Output Voltage Max: 250VAC
• Output Voltage Min: 30VDC
• Accuracy: 0.3%
• Approval: RoHS Compliant
• Brand/series: T16 Series
• Contact Form: SPST
• Dimensions: 49.5mmW×49.5mmH×115.3mmD
• Enclosure Rating: IP65
• Input Type: RTD/Thermocouple
• Ip Rating: IP65
• Memory: EEPROM
• Mounting Type: Panel
• Output Type: Relay
• Power, Rating: 8 VA
• Primary Type: Controller
• Special Features: EEPROM
• Standards: cURus, CE
• Termination: Screw
• Voltage, Supply: 85 to 250 VAC
• Lead Free Status / Rohs Status: RoHS Compliant part

The following parameters can be configured for
set to current. They must be changed if voltage output is desired. The Analog
output can be calibrated to provide up to approximately 5% over range
operation (0 mA current can only go slightly negative).
track.
actuator or pen recorder activity.
7.3 MODULE 3 - L
SETPOINT
dISP
HIdE
LOC
dSPr
ACCESS
ANtP
4-20
Select the type of output and range. The Analog output jumpers are factory
ANAS
This setting selects the parameter that the Analog Output will retransmit or
ANUt
The update time of the Analog Output can be used to reduce excess valve
dISP
SELECTION
OP
SP
(SP only)
0
ANALOG OUTPUT ASSIGNMENT (OPTIONAL)
ANALOG OUTPUT RANGE (OPTIONAL)
0-10
4-20
0
0
InP
ANALOG UPDATE TIME (OPTIONAL)
OP
SP
= update rate of 0.1 second
to
Display: accessible in Display Loop.
Hide: accessible in Hidden Loop.
Locked: not accessible in either loop.
Display/read: read only in Display Loop,
but read/write in Hidden Loop.
ACCESS
OUTPUT
POWER
dISP
mA
Main Control % Output Power
Input Signal Retransmission
Active Setpoint
V
250
OP
0-20
seconds
DESCRIPTION
mA
PID VALUES
ACCESS
HIdE
PId
OCKOUT
LOC
,
HIdE
PARAMETER MENU
, and
ACCESS
VALUES
ALARM
HIdE
P
ARAMETERS
AL
dISP
.
15
output as selected.
output as selected. An inverse acting output can be achieved by reversing the
low and high scaling points.
The following parameters can be configured for
100. 0
0&(,
The Analog Output assignment value that corresponds to 0 V, 0 mA or 4 mA
ANHI
The Analog Output assignment value that corresponds to 10 V or 20 mA
CodE
0. 0
0
SETPOINT
ACCESS
SELECT
SPSL
(
-1
LOC
ANALOG HIGH SCALING (OPTIONAL)
1
ANALOG LOW SCALING (OPTIONAL)
'%( ( )
-125
to
to
%...
0
-999
AUTO-TUNE
-125
125
ACCESS
START
tUNE
HIdE
to
to
)
Full access to Display, Hidden,
and Configuration Loops
Code necessary to access
Configuration Loop only.
Code necessary to access
Hidden and Configuration Loops.
to
ACCESS CODE
(!)
....
9999
SETPOINT
ACCESS
SPrP
HIdE
RAMP
ALARMS
ACCESS
RESET
ALrS
LOC
TRANSFER
CONTROL
ACCESS
LOC
trnF
LOC
or
HIdE
only
.