SP100R BANNER ENGINEERING, SP100R Datasheet - Page 13

• Manufacturer Part Number: SP100R
• Description: PHOTO SENSOR RECEIVER
• Manufacturer: BANNER ENGINEERING

Specifications of SP100R

• Output Current: 150mA
• Sensor Output: NPN Open Collector
• Supply Voltage Range Dc: 10V To 30V
• Leaded Process Compatible: No
• Peak Reflow Compatible (260 C): No

MICRO-AMP MA4L Specifications
MICRO-AMP
MA4L Latch Logic Module
MICRO-AMP
unlatched with low-going signals to its SET and RESET inputs. It also will function
as an edge-triggered "D" flip-flop latch when signals are presented to its INPUT pin.
The edge-triggered latch may be interrogated with a second signal at the INHIBIT
or the RESET pin. In this mode, the MA4L is very useful in inspection/rejection
applications. The MA4L may also be wired for alternate-action divide-by-two logic
(see logic diagram, below).
The MA4L directly accepts the outputs of other Banner MICRO-AMP modules plus
the NPN (current sinking) output of self-contained dc sensors.
Logic Truth Tables
TRUTH TABLE KEY
SUPPLY VOLTAGE: 10 to 30V dc at less than 20 milliamps
(exclusive of load); 10% maximum ripple.
INPUTS: INPUT, INHIBIT, RESET, and SET signals are buffered
for 1-millisecond response. A logic "low" must be less than 2V dc. A
logic "high" is at least 6V dc or an open circuit. Inputs must be capable
of sinking at least 4 milliamps. Inputs may be derived from limit
switches or from dc sensors with NPN (current sinking) output
transistors. INPUT signal polarity is selectable for either high-going
or low-going transition.
OUTPUT CONFIGURATION: two open-collector NPN transis-
tors with complementary outputs (one normally open, one normally
closed). Maximum sinking current 150 milliamps, each output.
Saturation voltage less than 0.5V dc at 10 milliamps. Off-state leakage
current less than 1 microamp.
RESPONSE SPEED: all inputs will respond to a low signal or a high
signal of 1 millisecond duration or longer.
CIRCUIT PROTECTION: reverse voltage polarity protected.
Latch comes up reset after power-up.
SELECTOR SWITCH: single-turn potentiometer selects response
polarity of INPUT. Fully clockwise = high-going transition; fully
counterclockwise = low-going transition.
INDICATOR: red LED indicator on the top of the module lights
whenever the N/O output is conducting.
H = logic HIGH
L = logic LOW
X = either HIGH or LOW (does not matter)
NC = no change of state
Set/reset latch mode, MA4L:
OUTPUT
= HIGH to LOW transition
= LOW to HIGH transition
RESET
SET
®
model MA4L offers two latching logic modes. It can be latched and
*
*NOTE: both outputs
conduct in this
condition (*).
®
System
Edge-triggered latch mode, MA4L:
OUTPUT
RESET
INPUT
SET-RESET LATCH MODE
(no connections to INPUT or INHIBIT)
Indicator LED
SET (pin #2)
RESET (pin #1)
N/O OUTPUT
(pin #6)
N/C OUTPUT
(pin #5)
CONSTRUCTION: totally encapsulated plug-in package with
molded VALOX
OPERATING TEMPERATURE:
0 to 70 degrees C (32 to 158 degrees F).
Functional Schematic MA4L LATCH Module
Off
Hookup Diagram, MA4L LATCH Module
H
L
H
L
On
L
H
L
H
On
L
L
L*
L*
®
Input Polarity:
INPUT (pin #7)
INHIBIT (pin #8) or
RESET (pin #1)
N/O OUTPUT
(pin #6)
N/C OUTPUT
(pin #5)
Indicator LED
housing. Gold-flashed connection pins.
EDGE-TRIGGERED LATCH MODE
Flip-flop ( 2) logic, MA4L:
(at pin #5)
OUTPUT
NOTE: Jumper pin #8 (INHIBIT) to
INPUT
(no connections to SET)
H
L
H
On
pin #6 (N/O Output)
L
H
L
Off
X
NC
NC
NC
H
L
H
On
L
H
L
Off
X
NC
NC
NC
13