QDE-825D BANNER ENGINEERING, QDE-825D Datasheet - Page 40

• Manufacturer Part Number: QDE-825D
• Description: Safety Light Curtain
• Manufacturer: BANNER ENGINEERING

Specifications of QDE-825D

• Light Curtain Type: Safety
• Accessory Type: Machine Interface Cable
• For Use With: EZ-Screen Safety Light Screen

38
38
After the initial trip test has been accomplished, the OSSD
safety outputs and EDM connections have been made to the
machine to be controlled, the EZ-SCREEN is ready for testing in
combination with the guarded machine.
The operation of the EZ-SCREEN with the guarded machine
must be verified before the combined EZ-SCREEN and machine
may be put into service. To do this, a Qualified Person must
perform the Commissioning Checkout Procedure described
in Section 6.2.
Figure 3-19. Emitters and receivers interchange easily when 8-pin connectors are used for both (optional hookup)
Figure 3-20. Emitter; generic hookup
3.6 Preparing for System Operation
P/N 133487
P/N 112852 rev. F
Installation and Alignment
*NOTE: Pins 2, 3, 4, 5, and 8 are not connected, or are paralleled to
Overview
8-pin male
Euro-style
Emitter
same color wire from the 8-pin receiver cable (see Section 3.7
and Figure 3-16).
†
Individual 8-wire Cordsets
Bn (#1)
Gn/Ye (#7)
Bu (#6)
Bk (#5)
Wh (#4)
Vi (#8)
Or (#3)
Or/Bk (#2)
Emitter (Standard)
QDE-8..D Cables
Bn
Or/Bk
Or
Wh
Bk
Bu
Gn/Ye
Vi
n.c.*
n.c.*
n.c.*
n.c.*
n.c.*
+24 dc
+24 dc
EDM2 / Aux
EDM1
OSSD2
OSSD1
0V dc
Ground
Reset
Receiver
0V dc
Figure 3-16 illustrates an optional hookup that provides sensor
interchangeability (or “swapability”) – the ability to install either
sensor at either QD connection. To hook up an 8-pin QD emitter,
use only three conductors (Brown = +24V dc, Blue = 0V dc,
Green/Yellow = GND). Connect the remaining wires in a parallel
connection (color-for-color) to the receiver cable.
The resulting installation provides the ability to swap the emitter
and receiver position, similar to a popular feature of Banner
MACHINE-GUARD
safety light screens. This hookup option provides advantages
during installation, wiring, and troubleshooting.
3.7 Sensor “Swapability” and the Optional Emitter Hookup
Model CSB.. splitter cordsets and DEE2R.. double-ended cables allow easy
interconnection between an EZ-SCREEN receiver and emitter, providing a single
“homerun” cable for the optional “swapable” hookup (see Section 2.2 Cables).
See above or
Section 2.2
for pinout
†
See Table 2.2 for further cable information.
5-pin male
Euro-style
Emitter
†
Gn/Ye (#5)
Bn (#1)
Bu (#3)
Wh (#2)
Bk (#4)
8-wire Splitter Cordsets
™
, MINI-SCREEN
Banner Engineering Corp.
Banner Engineering Corp.
Emitter (with Test)
www.bannerengineering.com • Tel: [phone]
www.bannerengineering.com • Tel: [phone]
Jumper
or
+24 dc
®
CSB.. Splitter Cordset
and MICRO-SCREEN
Instruction Manual
Receiver
open to test
•
•
DEE2R..
Minneapolis, U.S.A.
Minneapolis, U.S.A.
0V dc
EZ-SCREEN
®