LSM303DLH STMicroelectronics, LSM303DLH Datasheet - Page 30

• Manufacturer Part Number: LSM303DLH
• Description: IC, DIGITAL COMPASS, ±2g ±4g ±8g, LGA-28
• Manufacturer: STMicroelectronics
• Series: -r

Specifications of LSM303DLH

• No. Of Axes: 3
• Ic Interface Type: I2C, Serial
• Sensor Case Style: LGA
• No. Of Pins: 28
• Supply Voltage Range: 2.5V To 3.3V
• Acceleration Range: ± 2g, ± 4g, ± 8g
• Sensing Axis: Triple
• Acceleration: 2 g, 4 g, 8 g
• Sensitivity: 1 mg/digit, 2 mg/digit, 3.9 mg/digit
• Package / Case: LGA-28L
• Output Type: Linear
• Digital Output - Number Of Bits: 16 bit
• Supply Voltage (max): 3.3 V
• Supply Voltage (min): 2.5 V
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 30 C
• Digital Output - Bus Interface: I2C
• Package Type: LGA
• Operating Supply Voltage (min): 2.5V
• Operating Temperature (max): 85C
• Operating Temperature Classification: Commercial
• Product Depth (mm): 5mm
• Product Height (mm): 1mm
• Product Length (mm): 5mm
• Mounting: Surface Mount
• Pin Count: 28
• Sensor Type: Accelerometer and Magnetometer
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• For Use With: 497-10689 - BOARD ADAPTER LSM303DLH DIL24497-10508 - BOARD EVAL FOR MEMS SENSORS

Registers description
9.1.2
30/47
Table 20.
Table 21.
CTRL_REG2_A (21h)
Table 22.
Table 23.
The BOOT bit is used to refresh the content of internal registers stored in the Flash memory
block. At device power-up, the content of the Flash memory block is transferred to the
BOOT
HPM1, HPM0
FDS
HPen2
HPen1
HPCF1,
HPCF0
BOOT
PM2
0
0
1
1
1
DR1
0
0
1
1
Power mode and low-power output data rate configurations (continued)
Normal-mode output data rate configurations and low-pass cut-off
frequencies
CTRL_REG2_A register
CTRL_REG2_A description
HPM1
PM1
Reboot memory content. Default value: 0
(0: normal mode; 1: reboot memory content)
High-pass filter mode selection. Default value: 00
(00: normal mode; Others: refer to
Filtered data selection. Default value: 0
(0: internal filter bypassed; 1: data from internal filter sent to output register)
High-pass filter enabled for interrupt 2 source. Default value: 0
(0: filter bypassed; 1: filter enabled)
High-pass filter enabled for interrupt 1 source. Default value: 0
(0: filter bypassed; 1: filter enabled)
High-pass filter cut-off frequency configuration. Default value: 00
(00: HPc=8; 01: HPc=16; 10: HPc=32; 11: HPc=64)
1
1
0
0
1
DR0
0
1
0
1
HPM0
PM0
0
1
0
1
0
Doc ID 16941 Rev 1
Output data rate [Hz]
FDS
Power mode selection
ODR
1000
100
400
50
Low-power
Low-power
Low-power
Low-power
Low-power
Table
HPen2
24)
HPen1
Low-pass filter cut-off
Output data rate [Hz]
frequency [Hz]
HPCF1
ODR
292
780
37
74
0.5
10
1
2
5
LSM303DLH
LP
HPCF0