AT80C51RD2-3CSUM Atmel, AT80C51RD2-3CSUM Datasheet - Page 32

• Manufacturer Part Number: AT80C51RD2-3CSUM
• Description: IC, 8BIT MCU, 80C51, 40MHZ, DIP-40
• Manufacturer: Atmel

Specifications of AT80C51RD2-3CSUM

• Controller Family/series: 80C51
• No. Of I/o's: 32
• Ram Memory Size: 1280Byte
• Cpu Speed: 40MHz
• No. Of Timers: 3
• No. Of Pwm Channels: 5
• Digital Ic Case Style: DIP
• Core Size: 8 Bit
• Rohs Compliant: Yes
• Processor Series: AT80x
• Core: 8051
• Data Bus Width: 8 bit
• Program Memory Type: ROMLess
• Data Ram Size: 1280 B
• Interface Type: UART, SPI
• Maximum Clock Frequency: 60 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 3
• Operating Supply Voltage: 2.7 V to 5.5 V
• Maximum Operating Temperature: + 70 C
• Mounting Style: Through Hole
• Package / Case: PDIL-40
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Minimum Operating Temperature: 0 C
• Cpu Family: AT80
• Device Core: 8051
• Device Core Size: 8b
• Frequency (max): 40MHz
• Program Memory Size: Not Required
• Total Internal Ram Size: 1.25KB
• # I/os (max): 32
• Number Of Timers - General Purpose: 3
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 2.7V
• Instruction Set Architecture: CISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Through Hole
• Pin Count: 40
• Package Type: PDIP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Figure 10-5. PCA High-speed Output Mode
10.4
32
Pulse Width Modulator Mode
CCAPnH
AT80C51RD2
Write to
1
CCA PnL
Write to
0
Before enabling ECOM bit, CCAPnL and CCAPnH should be set with a non zero value, other-
wise an unwanted match could occur.
Once ECOM is set, writing CCAPnL will clear ECOM so that an unwanted match doesn’t occur
while modifying the compare value. Writing to CCAPnH will set ECOM. For this reason, user
software should write CCAPnL first, and then CCAPnH. Of course, the ECOM bit can still be
controlled by accessing the CCAPMn register.
All of the PCA modules can be used as PWM outputs. Figure 10-6 shows the PWM function.
The frequency of the output depends on the source for the PCA timer. All of the modules will
have the same frequency of output because they all share the PCA timer. The duty cycle of each
module is independently variable using the module's capture register CCAPLn. When the value
of the PCA CL SFR is less than the value in the module's CCAPLn SFR the output will be low,
when it is equal to or greater than the output will be high. When CL overflows from FF to 00,
CCAPLn is reloaded with the value in CCAPHn. This allows updating the PWM without glitches.
The PWM and ECOM bits in the module's CCAPMn register must be set to enable the PWM
mode.
Reset
Enable
PCA counter/timer
CCAPnH
CH
16 bit comparator
CF
ECOMn
CCAPnL
CR
CL
CAPPn
Match
CAPNn MATn TOGn PWMn ECCFn
CCF4 CCF3 CCF2 CCF1 CCF0
CCON
0xD8
CCAPMn, n = 0 to 4
0xDA to 0xDE
PCA IT
CEXn
4113D–8051–01/09