LIS302DLH STMicroelectronics, LIS302DLH Datasheet - Page 30

• Manufacturer Part Number: LIS302DLH
• Description: SENSOR ACCELEROMETER 3AXIS 14LGA
• Manufacturer: STMicroelectronics

Specifications of LIS302DLH

• Featured Product: STM32 Cortex-M3 Companion Products
• Axis: X, Y, Z
• Acceleration Range: ±2.3g, 9.2g
• Sensitivity: 18mg/digit, 72mg/digit
• Voltage - Supply: 2.16 V ~ 3.6 V
• Output Type: Digital
• Bandwidth: 100Hz ~ 400Hz Selectable
• Interface: I²C, SPI
• Mounting Type: Surface Mount
• Package / Case: 14-LGA
• Package Type: LGA
• Operating Supply Voltage (min): 2.16V
• Operating Supply Voltage (typ): 2.5V
• Operating Supply Voltage (max): 3.6V
• Operating Temperature (min): -40C
• Operating Temperature (max): 85C
• Operating Temperature Classification: Industrial
• Product Depth (mm): 3mm
• Product Height (mm): 0.92mm
• Product Length (mm): 5mm
• Mounting: Surface Mount
• Pin Count: 14
• Sensing Axis: Triple
• Acceleration: 2 g, 4 g, 8 g
• Digital Output - Number Of Bits: 16 bit
• Supply Voltage (max): 3.6 V
• Supply Voltage (min): 2.16 V
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Digital Output - Bus Interface: I2C, SPI
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 497-10052

Register description
7.10
7.11
7.12
7.13
30/37
Table 36.
OUT_X_L (28h), OUT_X_H (29h)
X-axis acceleration data. The value is expressed as two’s complement.
OUT_Y_L (2Ah), OUT_Y_H (2Bh)
Y-axis acceleration data. The value is expressed as two’s complement.
OUT_Z_L (2Ch), OUT_Z_H (2Dh)
Z-axis acceleration data. The value is expressed as two’s complement.
INT1_CFG (30h)
Table 37.
Table 38.
ZYXDA
ZDA
YDA
XDA
AOI
6D
ZHIE
ZLIE
AOI
STATUS_REG description (continued)
INT1_CFG register
INT1_CFG description
X, Y and Z axis new data available. Default value: 0
(0: a new set of data is not yet available; 1: a new set of data is available)
Z axis new data available. Default value: 0
(0: a new data for the Z-axis is not yet available;
1: a new data for the Z-axis is available)
Y axis new data available. Default value: 0
(0: a new data for the Y-axis is not yet available;
1: a new data for the Y-axis is available)
X axis new data available. Default value: 0
(0: a new data for the X-axis is not yet available;
1: a new data for the X-axis is available)
AND/OR combination of Interrupt events. Default value: 0.
(See
6 direction detection function enable. Default value: 0.
(See
Enable interrupt generation on Z high event. Default value: 0
(0: disable interrupt request;
1: enable interrupt request on measured accel. value higher than preset threshold)
Enable interrupt generation on Z low event. Default value: 0
(0: disable interrupt request;
1: enable interrupt request on measured accel. value lower than preset threshold)
6D
Table
Table
39)
39)
ZHIE
Doc ID 15797 Rev 1
ZLIE
YHIE
YLIE
XHIE
LIS302DLH
XLIE