LIS3LV02DLTR STMicroelectronics, LIS3LV02DLTR Datasheet - Page 22

IC MEMS INERTL SENSOR 3AX LGA16

LIS3LV02DLTR

Manufacturer Part Number
LIS3LV02DLTR
Description
IC MEMS INERTL SENSOR 3AX LGA16
Manufacturer
STMicroelectronics
Datasheet

Specifications of LIS3LV02DLTR

Featured Product
STM32 Cortex-M3 Companion Products
Axis
X, Y, Z
Acceleration Range
±2g, 6g
Sensitivity
1024LSB/g, 340LSB/g
Voltage - Supply
2.16 V ~ 3.6 V
Output Type
Digital
Bandwidth
40Hz ~ 2.56kHz Selectable
Interface
I²C, SPI
Mounting Type
Surface Mount
Package / Case
16-LGA
Family Name
LIS3LV02DL
Package Type
LGA
Operating Supply Voltage (min)
2.16V
Operating Supply Voltage (typ)
3.3V
Operating Supply Voltage (max)
3.6V
Operating Temperature (min)
-40C
Operating Temperature (max)
85C
Operating Temperature Classification
Industrial
Product Depth (mm)
4.4mm
Product Length (mm)
7.5mm
Mounting
Surface Mount
Pin Count
16
Sensing Axis
X, Y, Z
Acceleration
2 g, 6 g
Digital Output - Number Of Bits
12 bit, 16 bit
Supply Voltage (max)
3.6 V
Supply Voltage (min)
2.16 V
Supply Current
0.65 mA
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Digital Output - Bus Interface
I2C, SPI
For Use With
497-8261 - BOARD EVAL BASED ON LIS3LV02DL497-5069 - EVAL BOARD 3AXIS MEMS ACCELLRMTR
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
497-8415-2
LIS3LV02DLTR

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
LIS3LV02DLTR
Manufacturer:
ST
0
Digital interfaces
5
5.1
22/48
Digital interfaces
The registers embedded inside the LIS3LV02DL may be accessed through both the I
SPI serial interfaces. The latter may be SW configured to operate either in 3-wire or 4-wire
interface mode.
The serial interfaces are mapped onto the same pads. To select/exploit the I
line must be tied high (i.e connected to Vdd_IO).
Table 9.
I
The LIS3LV02DL I
whose content can also be read back.
The relevant I
Table 10.
There are two signals associated with the I
Serial DAta line (SDA). The latter is a bidirectional line used for sending and receiving the
data to/from the interface. Both the lines are connected to Vdd_IO through a pull-up resistor
embedded inside the LIS3LV02DL. When the bus is free both the lines are high.
The I
Normal Mode.
2
C serial interface
SDA/SDI/SDO
Transmitter
Pin name
SCL/SPC
2
Receiver
Master
C interface is compliant with Fast Mode (400 kHz) I
Slave
Term
SDO
CS
Serial interface pin description
Serial interface pin description
2
C terminology is given in the table below.
2
SPI enable
I
I
SPI Serial Port Clock (SPC)
I
SPI Serial Data Input (SDI)
3-wire Interface Serial Data Output (SDO)
SPI Serial Data Output (SDO)
The device which sends data to the bus
The device which receives data from the bus
The device which initiates a transfer, generates clock signals and terminates a
transfer
The device addressed by the master
C is a bus slave. The I
2
2
2
C/SPI mode selection (1: I
C Serial Clock (SCL)
C Serial Data (SDA)
2
C is employed to write the data into the registers
2
C bus: the Serial Clock Line (SCL) and the
2
C mode; 0: SPI enabled)
Pin description
Description
2
C standards as well as the
2
C interface, CS
LIS3LV02DL
2
C and

Related parts for LIS3LV02DLTR