PCF85176T/1,118 NXP Semiconductors, PCF85176T/1,118 Datasheet - Page 7

• Manufacturer Part Number: PCF85176T/1,118
• Description: IC LCD DISPLAY DVR 40SEG 56TSSOP
• Manufacturer: NXP Semiconductors

Specifications of PCF85176T/1,118

• Package / Case: 56-TFSOP (0.240", 6.10mm Width)
• Display Type: LCD
• Configuration: 40 Segment
• Interface: I²C
• Current - Supply: 20µA
• Voltage - Supply: 1.8 V ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Number Of Digits: 20
• Number Of Segments: 40
• Maximum Clock Frequency: 2640 Hz
• Operating Supply Voltage: 1.8 V to 5.5 V
• Maximum Power Dissipation: 400 mW
• Maximum Operating Temperature: + 95 C
• Attached Touch Screen: No
• Maximum Supply Current: 20 uA
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Digits Or Characters: -
• Lead Free Status / Rohs Status: Details
• Other names: 568-5933-2; PCF85176T/1,118

NXP Semiconductors
PCF85176_1
Product data sheet
7.2 LCD bias generator
7.3 LCD voltage selector
Remark: Do not transfer data on the I
the reset action to complete.
Fractional LCD biasing voltages are obtained from an internal voltage divider of the three
series resistors connected between V
switch if the
The LCD voltage selector coordinates the multiplexing of the LCD in accordance with the
selected LCD drive configuration. The operation of the voltage selector is controlled by the
mode-set command from the command decoder. The biasing configurations that apply to
the preferred modes of operation, together with the biasing characteristics as functions of
V
Table 5.
A practical value for V
threshold voltage (V
the static drive mode a suitable choice is V
Multiplex drive modes of 1:3 and 1:4 with
hence the contrast ratios are smaller.
Bias is calculated by
The RMS on-state voltage (V
where the values for n are
V
LCD drive
mode
static
1:2 multiplex 2
1:2 multiplex 2
1:3 multiplex 3
1:4 multiplex 4
LCD
•
on RMS
a = 1 for
a = 2 for
n = 1 for static drive mode
n = 2 for 1:2 multiplex drive mode
n = 3 for 1:3 multiplex drive mode
n = 4 for 1:4 multiplex drive mode
(
Display is disabled
and the resulting discrimination ratios (D) are given in
)
=
Biasing characteristics
1
1
⁄
⁄
V
2
3
1
LCD
⁄
2
Number of:
Backplanes Levels
1
bias
bias
bias voltage level for the 1:2 multiplex configuration is selected.
All information provided in this document is subject to legal disclaimers.
----------------------------- -
n
a
2
×
th
+
(
------------ -
1
), typically when the LCD exhibits approximately 10 % contrast. In
1
LCD
2a
1
+
Rev. 01 — 14 April 2010
+
a
+
a
is determined by equating V
)
, where the values for a are
n
2
3
4
4
4
2
on(RMS)
LCD bias
configuration
static
1
1
1
1
⁄
⁄
⁄
⁄
) for the LCD is calculated with
2
3
3
3
LCD
2
C-bus for at least 1 ms after a power-on to allow
and V
1
Universal LCD driver for low multiplex rates
⁄
LCD
2
bias are possible but the discrimination and
> 3V
SS
. The center resistor is bypassed by
th
0
0.354
0.333
0.333
0.333
V
------------------------ -
.
off RMS
V
off(RMS)
LCD
(
Table
)
with a defined LCD
1
0.791
0.745
0.638
0.577
V
----------------------- -
on RMS
V
5.
(
LCD
Equation
PCF85176
)
© NXP B.V. 2010. All rights reserved.
∞
2.236
2.236
1.915
1.732
D
=
1:
------------------------ -
V
V
off RMS
on RMS
(
(
7 of 43
)
(1)
)