WM8351GEB/V Wolfson Microelectronics, WM8351GEB/V Datasheet - Page 39

• Manufacturer Part Number: WM8351GEB/V
• Description: Audio CODECs Audio CODEC plus pwr management
• Manufacturer: Wolfson Microelectronics

Specifications of WM8351GEB/V

• Number Of Adc Inputs: 2
• Number Of Dac Outputs: 2
• Conversion Rate: 48 KSPS
• Interface Type: Serial (2-Wire, 3-Wire, 4-Wire)
• Resolution: 12 bit
• Operating Supply Voltage: 3.7 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Package / Case: BGA
• Minimum Operating Temperature: - 25 C
• Number Of Channels: 2 ADC/2 DAC
• Supply Current: 260 uA
• Thd Plus Noise: - 83 dB
• Audio Codec Type: Stereo
• No. Of Adcs: 2
• No. Of Dacs: 2
• No. Of Input Channels: 8
• No. Of Output Channels: 6
• Adc / Dac Resolution: 24bit
• Adcs / Dacs Signal To Noise Ratio: 95dB
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Production Data
11.3 2-WIRE SERIAL CONTROL MODE
Figure 23 Control Interface 2-wire Register Write
w
The 2-wire control interface normally uses the SCLK and SDATA pins, which are referenced to the
digital buffer supply, DBVDD. (In Development mode, the interface is initially redirected, with GPIO10
and GPIO11 effectively replacing SCLK and SDATA - see Section 14.4.1).
2-wire control mode is selected by setting SPI_3WIRE = 0. This is the default setting for this field.
In 2-wire mode, the WM8351 is a slave device on the control interface; SCLK (or GPIO10) is a clock
input, while SDATA (or GPIO11) is a bi-directional data pin. To allow arbitration of multiple slaves
(and/or multiple masters) on the same interface, the WM8351 transmits logic 1 by tri-stating the
SDATA pin, rather than pulling it high. An external pull-up resistor is required to pull the SDATA line
high so that the logic 1 can be recognised by the master.
Many devices can be controlled by the same bus, and each device has a unique 7-bit device ID (this
is not the same as the 8-bit address of each register in the WM8351). The default device ID is
0011 0100 (0x34h). The LSB of the device ID is the Read/Write bit; this bit is set to logic 1 for “Read”
and logic 0 for “Write”. In Development Mode, the device ID may be changed to other values.
The controller indicates the start of data transfer with a high to low transition on SDATA while SCLK
remains high. This indicates that a device ID, register address and data will follow. All devices on the
2-wire bus respond to the start condition and shift in the next eight bits on SDATA (7-bit device ID +
Read/Write bit, MSB first). If the device ID received matches the device ID of the WM8351, then the
WM8351 responds by pulling SDATA low on the next clock pulse (ACK). If the device ID is not
recognised or the R/W bit is ‘1’ when operating in write only mode, the WM8351 returns to the idle
condition and waits for a new start condition and valid address.
If the device ID matches the device ID of the WM8351, the data transfer continues as described
below. The controller indicates the end of data transfer with a low to high transition on SDATA while
SCKL remains high. After receiving a complete address and data sequence the WM8351 returns to
the idle state and waits for another start condition. If a start or stop condition is detected out of
sequence at any point during data transfer (i.e. SDATA changes while SCLK is high), the device
returns to the idle condition.
The WM8351 supports the following read and write operations:
The sequence of signals associated with a single register write operation is illustrated in Figure 23.
•
•
•
•
Single write
Single read
Multiple write using auto-increment
Multiple read using auto-increment
PD, March 2010, Rev 4.2
WM8351
39