PIC18F86J72-I/PT Microchip Technology, PIC18F86J72-I/PT Datasheet - Page 204

• Manufacturer Part Number: PIC18F86J72-I/PT
• Description: IC PIC MCU 8BIT 14KB FLSH 80TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F86J72-I/PT

• Program Memory Type: FLASH
• Program Memory Size: 64KB (32K x 16)
• Package / Case: 80-TQFP
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 48MHz
• Connectivity: I²C, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LCD, LVD, POR, PWM, WDT
• Number Of I /o: 51
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 12x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Data Bus Width: 8 bit
• Data Ram Size: 4 KB
• Interface Type: SPI, USART, SPI, I2C
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 51
• Number Of Timers: 4
• Operating Supply Voltage: 2 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 14
• Controller Family/series: PIC18F
• No. Of I/o's: 51
• Ram Memory Size: 3923Byte
• Cpu Speed: 12MIPS
• No. Of Timers: 4
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

PIC18F87J72 FAMILY
18.4
The MSSP module in I
master and slave functions (including general call
support) and provides interrupts on Start and Stop bits
in hardware to determine a free bus (multi-master
function). The MSSP module implements the standard
mode specifications as well as 7-bit and 10-bit
addressing.
Two pins are used for data transfer:
• Serial clock (SCL) – RC3/SCK/SCL/SEG17
• Serial data (SDA) – RC4/SDI/SDA/SEG16
The user must configure these pins as inputs by setting
the TRISC<4:3> bits.
FIGURE 18-7:
DS39979A-page 204
SCL
SDA
I
2
C Mode
Read
Shift
Clock
MSb
Address Mask
Stop bit Detect
Match Detect
SSPADD reg
MSSP BLOCK DIAGRAM
(I
SSPBUF reg
SSPSR reg
Start and
2
2
C mode fully implements all
C™ MODE)
LSb
Write
Addr Match
Set, Reset
S, P bits
(SSPSTAT reg)
Internal
Data Bus
Preliminary
18.4.1
The MSSP module has six registers for I
These are:
• MSSP Control Register 1 (SSPCON1)
• MSSP Control Register 2 (SSPCON2)
• MSSP Status Register (SSPSTAT)
• Serial Receive/Transmit Buffer Register
• MSSP Shift Register (SSPSR) – Not directly
• MSSP Address Register (SSPADD)
SSPCON1, SSPCON2 and SSPSTAT are the control
and status registers in I
SSPCON1 and SSPCON2 registers are readable and
writable. The lower 6 bits of the SSPSTAT are
read-only. The upper two bits of the SSPSTAT are
read/write.
Many of the bits in SSPCON2 assume different
functions, depending on whether the module is operat-
ing in Master or Slave mode; bits<5:2> also assume
different names in Slave mode. The different aspects of
SSPCON2 are shown in Register 18-5 (for Master
mode) and Register 18-6 (Slave mode).
SSPSR is the shift register used for shifting data in or
out. SSPBUF is the buffer register to which data bytes
are written to or read from.
SSPADD register holds the slave device address when
the MSSP is configured in I
MSSP is configured in Master mode, the lower seven
bits of SSPADD act as the Baud Rate Generator reload
value.
In receive operations, SSPSR and SSPBUF together,
create a double-buffered receiver. When SSPSR
receives a complete byte, it is transferred to SSPBUF
and the SSPIF interrupt is set.
During transmission, the SSPBUF is not double-
buffered. A write to SSPBUF will write to both SSPBUF
and SSPSR.
(SSPBUF)
accessible
REGISTERS
 2010 Microchip Technology Inc.
2
2
C mode operation. The
C Slave mode. When the
2
C operation.