PIC18LF24K22-I/SS Microchip Technology, PIC18LF24K22-I/SS Datasheet - Page 42

• Manufacturer Part Number: PIC18LF24K22-I/SS
• Description: IC PIC MCU 16KB FLASH 28SSOP
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18LF24K22-I/SS

• Core Size: 8-Bit
• Program Memory Size: 16KB (8K x 16)
• Core Processor: PIC
• Speed: 64MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 24
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 19x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-SSOP (0.200", 5.30mm Width)
• Controller Family/series: PIC18
• No. Of I/o's: 25
• Eeprom Memory Size: 256Byte
• Ram Memory Size: 768Byte
• Cpu Speed: 64MHz
• No. Of Timers: 7
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

PIC18(L)F2X/4XK22
2.9.3
When switching between one oscillator and another,
the new oscillator may not be operating which saves
power (see
delay after the SCS<1:0> bits of the OSCCON register
are modified before the frequency change takes place.
The OSTS and IOFS bits of the OSCCON register will
reflect the current active status of the external and
HFINTOSC oscillators. The timing of a frequency
selection is as follows:
1.
2.
3.
4.
5.
6.
7.
See
If the HFINTOSC is the source of both the old and new
frequency, there is no start-up delay before the new
frequency is active. This is because the old and new
frequencies are derived from the HFINTOSC via the
postscaler and multiplexer.
Start-up
Section 27.0 “Electrical
Specifications (Oscillator Module).
DS41412D-page 42
SCS<1:0> bits of the OSCCON register are mod-
ified.
The old clock continues to operate until the new
clock is ready.
Clock switch circuitry waits for two consecutive
rising edges of the old clock after the new clock
ready signal goes true.
The system clock is held low starting at the next
falling edge of the old clock.
Clock switch circuitry waits for an additional two
rising edges of the new clock.
On the next falling edge of the new clock the low
hold on the system clock is released and new
clock is switched in as the system clock.
Clock switch is complete.
Figure 2-1
delay
CLOCK SWITCH TIMING
Figure
for more details.
2-9). If this is the case, there is a
specifications
Characteristics”, under AC
are
located
Preliminary
in
2.10
Two-Speed Start-up mode provides additional power
savings by minimizing the latency between external
oscillator start-up and code execution. In applications
that make heavy use of the Sleep mode, Two-Speed
Start-up will remove the external oscillator start-up
time from the time spent awake and can reduce the
overall power consumption of the device.
This mode allows the application to wake-up from
Sleep, perform a few instructions using the HFINTOSC
as the clock source and go back to Sleep without
waiting for the primary oscillator to become stable.
When the oscillator module is configured for LP, XT or
HS modes, the Oscillator Start-up Timer (OST) is
enabled (see
(OST)”). The OST will suspend program execution until
1024 oscillations are counted. Two-Speed Start-up
mode minimizes the delay in code execution by
operating from the internal oscillator as the OST is
counting. When the OST count reaches 1024 and the
OSTS bit of the OSCCON register is set, program
execution switches to the external oscillator.
2.10.1
Two-Speed Start-up mode is enabled when all of the
following settings are configured as noted:
• Two-Speed Start-up mode is enabled when the
• SCS<1:0> (of the OSCCON register) = 00.
• FOSC<2:0> bits of the CONFIG1H Configuration
Two-Speed Start-up mode becomes active after:
• Power-on Reset (POR) and, if enabled, after
• Wake-up from Sleep.
Note:
IESO of the CONFIG1H Configuration register is
set.
register are configured for LP, XT or HS mode.
Power-up Timer (PWRT) has expired, or
Two-Speed Clock Start-up Mode
Executing a SLEEP instruction will abort
the oscillator start-up time and will cause
the OSTS bit of the OSCCON register to
remain clear.
TWO-SPEED START-UP MODE
CONFIGURATION
Section 2.4.1 “Oscillator Start-up Timer
 2010 Microchip Technology Inc.