A16-1NGN Omron, A16-1NGN Datasheet - Page 161

• Manufacturer Part Number: A16-1NGN
• Description: NEON LAMP 110V GREEN FOR A16
• Manufacturer: Omron
• Type: Neon Lamp, 110 VoltsACr
• Series: A16r

Specifications of A16-1NGN

• Accessory Type: Neon Lamp Replacement
• Supply Voltage: 110V
• Base Type: Bi-Pin
• Colour: Green
• Current Rating: 1.5mA
• Svhc: No SVHC (15-Dec-2010)
• Illumination Colour: Green
• Operating Lifetime: 10000h
• Voltage Rating Vac: 110V
• Average Bulb Lif: RoHS Compliant
• Color: Green
• Illumination: Illuminated
• Height: 13 mm
• Illumination Color: Green
• Mounting Style: Snap In
• Termination Style: Tabs
• Lamp Base Type: Bi-Pin
• Rohs Compliant: Yes
• Average Bulb Life: 10000h
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With/related Products: A16 Series
• For Use With: Z1396 - SWTCH KNOB RND 3POS DPDT ILL GRNZ1393 - SWTCH KNOB RND 2POS SPDT ILL GRNZ1390 - SWTCH KNOB RND 2POS SPDT ILL GRNZ1384 - SWITCH KNB RECT 3POS DPDT ILLZ1381 - SWITCH KNB RECT 2POS SPDT ILLZ1378 - SWITCH KNB RECT 2POS SPDT ILLZ1372 - SWITCH KNOB SQ 3-POS DPDT ILLZ1369 - SWITCH KNOB SQ 2-POS SPDT ILLZ1366 - SWITCH KNOB SQ 2-POS SPDT ILLZ1308 - SWITCH PB RND MOM DPDT ILLUM GRNZ1304 - SWITCH PB RECT MOM DPDT ILLUMZ1300 - SWITCH PB SQ MOM DPDT ILLUM GRN
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: A161NGN; Z1343

Installation
Common to A22, A22S/W, A22K, M22, and A22E
Panel Hole Dimensions
For 25-dia. holes, always use 25-dia. Rings. (Since the cutout dimen-
sions are large, IP65 cannot be guaranteed unless 25-dia. Rings are
used.)
If outer surface treatment such as coating is performed for the panel,
the panel dimensions after outer surface treatment must meet the
specified panel dimensions.
Note: Recommended panel thickness: 1 to 5 mm.
Matrix Installation
1. The following panel hole dimensions apply when Switch Unit and
the Standard-size Legend Plate Frame and Lock Ring are
mounted, and lead wires are connected directly to the Switch
Block.
Mounting to the Panel
22 dia.
A
25 dia.
2. The following panel hole dimensions apply when the Large-size
Pitches A and B between the centers of the mounting holes are as
follows:
For 1. above:
For 2. above:
Note: 1. The above dimensions are the minimum dimensions for
A22-10, A22-10S, A22-01, A22-01S
A22-20, A22-20S, A22-02, A22-02S, A22-11,
A22-11S
Bare crimp termi-
nals
Crimp terminals
with insulating
sheath
Legend Plate Frame is mounted, and when crimp terminals are
connected to the Switch Block terminals.
Type of crimp
terminal
2. With pushbuttons of external dimensions greater than
3. When using a pushbutton with external dimensions exceed-
when the wires described under Applicable Wire Size on
page 165 are used. If a different wires are used, the wiring
dimensions may be different so determine an appropriate
pitch before setup.
30 mm, set the pitch according to the dimensions. (When
using matrix installation for the A22-M@, mount with a pitch
of 40 mm instead of 30 mm in the diagram above.)
ing 30 mm, use a pitch appropriate for the pushbutton.
Switch Blocks
A22-10, A22-10S, A22-01,
A22-01S
A22-20, A22-20S, A22-02,
A22-02S, A22-11, A22-11S
A22-10, A22-10S, A22-01,
A22-01S
A22-20, A22-20S, A22-02,
A22-02S, A22-11, A22-11S
Switch Blocks
B
45 mm min.
55 mm min.
51 mm min.
61 mm min.
60 mm min.
70 mm min.
A
B
159