IS-C0203-F-E NKK Switches, IS-C0203-F-E Datasheet - Page 16

• Manufacturer Part Number: IS-C0203-F-E
• Description: SMARTSWITCH CONTROLLER LCD
• Manufacturer: NKK Switches

Specifications of IS-C0203-F-E

• Accessory Type: Controller
• Description/function: SMARTSWITCH Development Kit
• For Use With/related Products: SmartSwitch™ Switches
• For Use With: 360-2345 - SWITCH COMPACT LCD 64X32 RGB360-2343 - SWITCH LCD 64X32 RGB360-2341 - DISPLAY LCD 64X32IS01BCEF - SMARTDISPLAY SUPER YEL/GRN LEDIS01BCE - SMARTDISPLAY SUPER YELLOW LEDIS15SBFP4B - SMARTSWITCH COMPACT WHITE LEDIS15SBCP4EF - SMARTSWITCH COMPACT YEL/GRN LEDIS15SACP4CF - SMARTSWITCH COMPACT RED/GRN LEDIS15ABFP4B - SMARTSWITCH STD BLK W/WHITE LEDIS15ABDP4B - SMARTSWITCH STD BLU W/WHITE LEDIS15ABDP4EG - SMARTSWITCH STD YELLOW/BLUE LEDIS15ABDP4E - SMARTSWITCH STD BLUE W/YEL LEDIS15ABCP4EF - SMARTSWITCH STD YEL/GRN LEDIS15ABCP4E - SMARTSWITCH STD LED YELLOWIS15AACP4CF - SMARTSWITCH STD YEL RED/GRN LED360-2334 - SMARTDISPLAY RED/GREEN/BLUE360-2333 - SMARTDISPLAY SUPER RED/GREEN LED360-2332 - SMARTSWITCH STANDARD RED/GRN/BLU360-2331 - SMARTSWITCH COMPACT RED/GRN/BLU360-2330 - SMARTSWITCH STD RED/GRN LED360-2329 - SMARTSWITCH COMPACT RED/GRN LED
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: 360-2425

7850 East Gelding Drive • Scottsdale, AZ 85260-3420
Command to write the setup values to the EPROM
Command to reset the setup values to the default values
Command to fill display with specified byte
[LCD Module #] is the switch number (31H for switch 1, 32H for switch 2)
[Byte] Specified byte.
Command to transfer the RAM to specified address
[LCD Module #] is the switch number (31H for switch 1, 32H for switch 2)
[Address] is one byte with value of 01H to FFH.
IS-Dev Kit-5 and IS-Dev Kit-6 Users Manual A.doc
This command writes the setup values to the flash as per the following table. Once commanded the
values become permanent.
This command writes the default values to the flash. Once commanded the values become permanent
after power up or reboot. Sets Addresses 01H and 02H memories to “BLANK FONT MEMORY”.
This command displays a specified byte over all of the display.
This command transfers the RAM to the specified address.
command format:
transmit format:
• LED press value
• LED brightness level
• LED off cycle duration
• LED on/off cycle ratio
• FLAG A
• FLAG B
• Timers for LED up/LED down
• Power up addresses
command format:
transmit format:
command format:
transmit format:
command format:
transmit format:
Toll Free 1.877.2BUYNKK (877.228.9655) • Phone [phone] • Fax [phone]
(xxH) (xxH) (xxH) (xxH) (xxH)
(xxH) (xxH) (xxH) (xxH) (xxH)
(xxH)
(xxH)
26H
26H
27H
27H
IS-Dev Kit-5 and IS-Dev Kit-6 Users
www.nkkswitches.com • Email [e-mail]
[LCD Module #]
[LCD Module #]
51H
51H
(31H or 32H)
(31H or 32H)
4EH
4FH
Manual
34H
34H
(xxH) (xxAH)
(xxH)
00H
02H
46H
45H
[Address]
[Byte]
(xxAH)
Page 16 of 24
1209