IS-C0203-F-E NKK Switches, IS-C0203-F-E Datasheet - Page 11

• Manufacturer Part Number: IS-C0203-F-E
• Description: SMARTSWITCH CONTROLLER LCD
• Manufacturer: NKK Switches

Specifications of IS-C0203-F-E

• Accessory Type: Controller
• Description/function: SMARTSWITCH Development Kit
• For Use With/related Products: SmartSwitch™ Switches
• For Use With: 360-2345 - SWITCH COMPACT LCD 64X32 RGB360-2343 - SWITCH LCD 64X32 RGB360-2341 - DISPLAY LCD 64X32IS01BCEF - SMARTDISPLAY SUPER YEL/GRN LEDIS01BCE - SMARTDISPLAY SUPER YELLOW LEDIS15SBFP4B - SMARTSWITCH COMPACT WHITE LEDIS15SBCP4EF - SMARTSWITCH COMPACT YEL/GRN LEDIS15SACP4CF - SMARTSWITCH COMPACT RED/GRN LEDIS15ABFP4B - SMARTSWITCH STD BLK W/WHITE LEDIS15ABDP4B - SMARTSWITCH STD BLU W/WHITE LEDIS15ABDP4EG - SMARTSWITCH STD YELLOW/BLUE LEDIS15ABDP4E - SMARTSWITCH STD BLUE W/YEL LEDIS15ABCP4EF - SMARTSWITCH STD YEL/GRN LEDIS15ABCP4E - SMARTSWITCH STD LED YELLOWIS15AACP4CF - SMARTSWITCH STD YEL RED/GRN LED360-2334 - SMARTDISPLAY RED/GREEN/BLUE360-2333 - SMARTDISPLAY SUPER RED/GREEN LED360-2332 - SMARTSWITCH STANDARD RED/GRN/BLU360-2331 - SMARTSWITCH COMPACT RED/GRN/BLU360-2330 - SMARTSWITCH STD RED/GRN LED360-2329 - SMARTSWITCH COMPACT RED/GRN LED
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: 360-2425

7850 East Gelding Drive • Scottsdale, AZ 85260-3420
The controller disables the timers and switch execution upon receiving this command. However, the switches
are still scanned and reported. They are enabled upon reboot/power up or by command from host.
Command to set LED codes
[LED for switch 1] is one byte for LCD 36x24 and two bytes for LCD 64x32 (first byte for on-cycle and second
byte for off cycle).
[LED for switch 2] is one byte for LCD 36x24 and two bytes for LCD 64x32 (first byte for on-cycle and second
byte for off cycle).
Command to transfer from EEPROM to internal RAM by Addresses
[Address for Switch 1] is one byte with value of 00H to FFH.
[Address for Switch 2] is one byte with value of 00H to FFH.
Command to transfer from EEPROM to internal RAM for one Address
[LCD Module #] is the switch number (31H for switch 1, 32H for switch 2)
[Address] is one byte with value of 01H to FFH.
IS-Dev Kit-5 and IS-Dev Kit-6 Users Manual A.doc
This command sets the LED backlights according to the command’s LED codes.
Example: The following hex string makes switch 1 display green for “ON/OFF CYCLE” and switch 2
display white for ‘ON CYCLE’ and red for “OFF CYCLE”
This command transfers the data from EEPROM to internal RAM according to the addresses. If either of
the address values is zero no transfer takes place for that address.
Example: The following hex string makes switch 1 display the data from location 5 and makes switch 2
display the data from location 6. 2D 00 3035 3036
This command updates the specified switch with the data from EEPROM using the address.
command format: 2CH
transmit format:
command format: 2DH
transmit format:
command format: 2EH [LCD Module #] [Address]
transmit format:
Toll Free 1.877.2BUYNKK (877.228.9655) • Phone [phone] • Fax [phone]
For LCD 36x24 mode
2C 00 3232 3137
(xxH) (xxAH)
(xxH) (xxH)
(xxH)
IS-Dev Kit-5 and IS-Dev Kit-6 Users
www.nkkswitches.com • Email [e-mail]
00H
00H
(31H or 32H)
[Address for Switch 1] [Address for Switch 2]
[LED for Switch 1] [LED for Switch 2]
(xxAH)
(xxAH)
Manual
(xxAH)
For LCD 64x32 mode
2C 00 3333 3333 4646 4233
(xxAH)
(xxAH)
Page 11 of 24
1209