IS-C0203-F-E NKK Switches, IS-C0203-F-E Datasheet - Page 13

• Manufacturer Part Number: IS-C0203-F-E
• Description: SMARTSWITCH CONTROLLER LCD
• Manufacturer: NKK Switches

Specifications of IS-C0203-F-E

• Accessory Type: Controller
• Description/function: SMARTSWITCH Development Kit
• For Use With/related Products: SmartSwitch™ Switches
• For Use With: 360-2345 - SWITCH COMPACT LCD 64X32 RGB360-2343 - SWITCH LCD 64X32 RGB360-2341 - DISPLAY LCD 64X32IS01BCEF - SMARTDISPLAY SUPER YEL/GRN LEDIS01BCE - SMARTDISPLAY SUPER YELLOW LEDIS15SBFP4B - SMARTSWITCH COMPACT WHITE LEDIS15SBCP4EF - SMARTSWITCH COMPACT YEL/GRN LEDIS15SACP4CF - SMARTSWITCH COMPACT RED/GRN LEDIS15ABFP4B - SMARTSWITCH STD BLK W/WHITE LEDIS15ABDP4B - SMARTSWITCH STD BLU W/WHITE LEDIS15ABDP4EG - SMARTSWITCH STD YELLOW/BLUE LEDIS15ABDP4E - SMARTSWITCH STD BLUE W/YEL LEDIS15ABCP4EF - SMARTSWITCH STD YEL/GRN LEDIS15ABCP4E - SMARTSWITCH STD LED YELLOWIS15AACP4CF - SMARTSWITCH STD YEL RED/GRN LED360-2334 - SMARTDISPLAY RED/GREEN/BLUE360-2333 - SMARTDISPLAY SUPER RED/GREEN LED360-2332 - SMARTSWITCH STANDARD RED/GRN/BLU360-2331 - SMARTSWITCH COMPACT RED/GRN/BLU360-2330 - SMARTSWITCH STD RED/GRN LED360-2329 - SMARTSWITCH COMPACT RED/GRN LED
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: 360-2425

7850 East Gelding Drive • Scottsdale, AZ 85260-3420
Command to uploads the FIRMWARE version
Command to set LED Brightness
[LED BRIGHTNESS] is one byte from 00H (dimmest) to 07H (brightest). The upper 5 bits of the byte are
ignored.
This command is for duration of the session. It can become permanent by “Command to write the setup
values to the EPROM”.
Command to set LED press value
[LED code] is one byte for LCD 36x24. B0 of FLAG A must be set. LCD 36x24 only
This command is for duration of the session. It can become permanent by “Command to write the setup
values to the EPROM”.
Command to set LED off cycle duration
[LED OFF cycle] is one byte.
This command is for duration of the session. It can become permanent by “Command to write the setup
values to the EPROM”.
IS-Dev Kit-5 and IS-Dev Kit-6 Users Manual A.doc
This command uploads the FIRMWARE version to the host in one byte HEX format.
This command sets the LED brightness for the duration of the session.
This command sets the LED code for when the switch is pressed. It applies to LCD 36x24 switches
only.
This command sets the duration of the off cycle.
command format:
transmit format:
command format:
transmit format:
command format:
transmit format:
command format:
transmit format:
Toll Free 1.877.2BUYNKK (877.228.9655) • Phone [phone] • Fax [phone]
(xxH) (xxH)
(xxH) (xxH) (xxH)
(xxH) (xxH) (xxH)
(xxH) (xxH) (xxH)
26H
26H
26H
26H
IS-Dev Kit-5 and IS-Dev Kit-6 Users
www.nkkswitches.com • Email [e-mail]
15H
51H
51H
51H
53H
55H
57H
[LED Brightness]
[LED code]
[LED OFF cycle]
Manual
(xxAH)
(xxAH)
(xxAH)
Page 13 of 24
1209