ATMEGA128RZAV-8MU Atmel, ATMEGA128RZAV-8MU Datasheet - Page 368

• Manufacturer Part Number: ATMEGA128RZAV-8MU
• Description: MCU ATMEGA1281/AT86RF230 64-QFN
• Manufacturer: Atmel
• Series: ATMEGAr

Specifications of ATMEGA128RZAV-8MU

• Frequency: 2.4GHz
• Data Rate - Maximum: 2Mbps
• Modulation Or Protocol: 802.15.4 Zigbee
• Applications: General Purpose
• Power - Output: 3dBm
• Sensitivity: -101dBm
• Voltage - Supply: 1.8 V ~ 3.6 V
• Data Interface: PCB, Surface Mount
• Memory Size: 128kB Flash, 4kB EEPROM, 8kB RAM
• Antenna Connector: PCB, Surface Mount
• Package / Case: 64-QFN
• For Use With: ATAVRISP2 - PROGRAMMER AVR IN SYSTEMATJTAGICE2 - AVR ON-CHIP D-BUG SYSTEMATSTK501 - ADAPTER KIT FOR 64PIN AVR MCUATSTK500 - PROGRAMMER AVR STARTER KIT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Operating Temperature: -
• Current - Transmitting: -
• Current - Receiving: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

T
Notes:
2549M–AVR–09/10
A
Symbol
I
V
I
t
CC
ACLK
ACID
ACIO
= -40°C to 85°C, V
1. "Max" means the highest value where the pin is guaranteed to be read as low.
2. "Min" means the lowest value where the pin is guaranteed to be read as high.
3. Although each I/O port can sink more than the test conditions (20mA at VCC = 5V, 10mA at VCC = 3V) under steady state
4. Although each I/O port can source more than the test conditions (20mA at VCC = 5V, 10mA at VCC = 3V) under steady
conditions (non-transient), the following must be observed:
ATmega1281/2561:
1.)The sum of all IOL, for ports A0-A7, G2, C4-C7 should not exceed 100 mA.
2.)The sum of all IOL, for ports C0-C3, G0-G1, D0-D7 should not exceed 100 mA.
3.)The sum of all IOL, for ports G3-G5, B0-B7, E0-E7 should not exceed 100 mA.
4.)The sum of all IOL, for ports F0-F7 should not exceed 100 mA.
ATmega640/1280/2560:
1.)The sum of all IOL, for ports J0-J7, A0-A7, G2 should not exceed 200 mA.
2.)The sum of all IOL, for ports C0-C7, G0-G1, D0-D7, L0-L7 should not exceed 200 mA.
3.)The sum of all IOL, for ports G3-G4, B0-B7, H0-B7 should not exceed 200 mA.
4.)The sum of all IOL, for ports E0-E7, G5 should not exceed 100 mA.
5.)The sum of all IOL, for ports F0-F7, K0-K7 should not exceed 100 mA.
If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current greater
than the listed test condition.
state conditions (non-transient), the following must be observed:
ATmega1281/2561:
1)The sum of all IOH, for ports A0-A7, G2, C4-C7 should not exceed 100 mA.
2)The sum of all IOH, for ports C0-C3, G0-G1, D0-D7 should not exceed 100 mA.
3)The sum of all IOH, for ports G3-G5, B0-B7, E0-E7 should not exceed 100 mA.
4)The sum of all IOH, for ports F0-F7 should not exceed 100 mA.
ATmega640/1280/2560:
1)The sum of all IOH, for ports J0-J7, G2, A0-A7 should not exceed 200 mA.
2)The sum of all IOH, for ports C0-C7, G0-G1, D0-D7, L0-L7 should not exceed 200 mA.
Parameter
Power Supply Current
Power-down mode
Analog Comparator
Input Offset Voltage
Analog Comparator
Input Leakage Current
Analog Comparator
Propagation Delay
CC
= 1.8V to 5.5V (unless otherwise noted) (Continued)
(5)
(ATmega640/1280/2560/1V)
Active 4MHz, V
(ATmega640/1280/2560/1L)
Active 8MHz, V
(ATmega640/1280/1281/2560/2561)
Idle 1MHz, V
WDT disabled, V
V
V
V
Condition
Active 1MHz, V
(ATmega640/1280/2560/1V)
Idle 4MHz, V
(ATmega640/1280/2560/1L)
Idle 8MHz, V
(ATmega640/1280/1281/2560/2561)
WDT enabled, V
V
V
V
CC
in
CC
in
CC
CC
= V
= V
= 5V
= 5V
= 2.7V
= 4.0V
CC
CC
/2
/2
CC
CC
CC
CC
CC
CC
= 2V
= 3V
= 5V
CC
CC
= 2V
= 3V
= 5V
= 3V
= 3V
ATmega640/1280/1281/2560/2561
Min.
-50
Typ.
0.14
<10
750
500
0.5
3.2
0.7
2.7
10
<5
<1
Max.
0.22
0.8
1.1
7.5
14
15
40
50
5
4
Units
mA
mV
µA
nA
ns
368