ATMEGA128RZAV-8MU Atmel, ATMEGA128RZAV-8MU Datasheet - Page 32

• Manufacturer Part Number: ATMEGA128RZAV-8MU
• Description: MCU ATMEGA1281/AT86RF230 64-QFN
• Manufacturer: Atmel
• Series: ATMEGAr

Specifications of ATMEGA128RZAV-8MU

• Frequency: 2.4GHz
• Data Rate - Maximum: 2Mbps
• Modulation Or Protocol: 802.15.4 Zigbee
• Applications: General Purpose
• Power - Output: 3dBm
• Sensitivity: -101dBm
• Voltage - Supply: 1.8 V ~ 3.6 V
• Data Interface: PCB, Surface Mount
• Memory Size: 128kB Flash, 4kB EEPROM, 8kB RAM
• Antenna Connector: PCB, Surface Mount
• Package / Case: 64-QFN
• For Use With: ATAVRISP2 - PROGRAMMER AVR IN SYSTEMATJTAGICE2 - AVR ON-CHIP D-BUG SYSTEMATSTK501 - ADAPTER KIT FOR 64PIN AVR MCUATSTK500 - PROGRAMMER AVR STARTER KIT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Operating Temperature: -
• Current - Transmitting: -
• Current - Receiving: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

8.1.5
2549M–AVR–09/10
Using all Locations of External Memory Smaller than 64 Kbytes
Figure 8-5.
Note:
Figure 8-6.
Note:
Since the external memory is mapped after the internal memory as shown in
28, the external memory is not addressed when addressing the first 8,704 bytes of data space. It
may appear that the first 8,704 bytes of the external memory are inaccessible (external memory
addresses 0x0000 to 0x21FF). However, when connecting an external memory smaller than 64
Kbytes, for example 32 Kbytes, these locations are easily accessed simply by addressing from
address 0x8000 to 0xA1FF. Since the External Memory Address bit A15 is not connected to the
external memory, addresses 0x8000 to 0xA1FF will appear as addresses 0x0000 to 0x21FF for
the external memory. Addressing above address 0xA1FF is not recommended, since this will
address an external memory location that is already accessed by another (lower) address. To
System Clock (CLK
System Clock (CLK
DA7:0 (XMBK = 0)
DA7:0 (XMBK = 1)
DA7:0 (XMBK = 0)
DA7:0 (XMBK = 1)
1. SRWn1 = SRW11 (upper sector) or SRW01 (lower sector), SRWn0 = SRW10 (upper sector) or
1. SRWn1 = SRW11 (upper sector) or SRW01 (lower sector), SRWn0 = SRW10 (upper sector) or
SRW00 (lower sector).
The ALE pulse in period T6 is only present if the next instruction accesses the RAM (internal
or external).
SRW00 (lower sector).
The ALE pulse in period T7 is only present if the next instruction accesses the RAM (internal
or external).
DA7:0
A15:8
CPU
ALE
DA7:0
WR
A15:8
RD
External Data Memory Cycles with SRWn1 = 1 and SRWn0 = 0
External Data Memory Cycles with SRWn1 = 1 and SRWn0 = 1
CPU
ALE
WR
)
RD
)
Prev. addr.
Prev. data
Prev. data
Prev. data
Prev. addr.
Prev. data
Prev. data
Prev. data
T1
T1
Address
Address
Address
ATmega640/1280/1281/2560/2561
T2
Address
Address
Address
XX
T2
XX
Address
T3
Data
Data
Data
Address
T3
Data
Data
Data
T4
T4
T5
T5
T6
Figure 8-1 on page
(1)
(1)
T6
T7
32