MNZB-24-B0 MeshNetics, MNZB-24-B0 Datasheet - Page 18

• Manufacturer Part Number: MNZB-24-B0
• Description: MOD 802.15.4/ZIGB 2.4GHZ RF PORT
• Manufacturer: MeshNetics
• Series: Zigbit™r

Specifications of MNZB-24-B0

• Frequency: 2.4GHz
• Data Rate - Maximum: 250kbps
• Modulation Or Protocol: 802.15.4 Zigbee
• Power - Output: 3dBm
• Sensitivity: -101dBm
• Voltage - Supply: 1.8 V ~ 3.6 V
• Current - Receiving: 19mA
• Current - Transmitting: 18mA
• Data Interface: PCB, Surface Mount
• Memory Size: 128kBytes Flash, 8kBytes RAM, 4kBytes EEPROM
• Antenna Connector: PCB, Surface Mount
• Operating Temperature: -40°C ~ 85°C
• Package / Case: Module
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Applications: -
• Other names: 758-1000-2; ZDM-A1281-B0

Agency Certifications
UNITED STATES (FCC)
WARNING: The Original Equipment Manufacturer (OEM) must ensure that the OEM modular transmitter must be
IMPORTANT: This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two
IMPORTANT: Modifications not expressly approved by this company could void the user's authority to operate this
IMPORTANT: This equipment has been tested and found to comply with the limits for a Class A digital device,
© 2007 MeshNetics
This equipment complies with Part 15 of the FCC rules and regulations.
To fulfill FCC Certification requirements, an OEM manufacturer must comply with the following
regulations:
labeled with its own FCC ID number. This includes a clearly visible label on the outside of the final
product enclosure that displays the contents shown below. If the FCC ID is not visible when the
equipment is installed inside another device, then the outside of the device into which the equipment is
installed must also display a label referring to the enclosed equipment.
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation (FCC 15.19).
The internal / external antenna(s) used for this mobile transmitter must provide a separation distance of
at least 20 cm from all persons and must not be co-located or operating in conjunction with any other
antenna or transmitter.
Installers must be provided with antenna installation instructions and transmitter operating conditions for
satisfying RF exposure compliance. This device is approved as a mobile device with respect to RF
exposure compliance, and may only be marketed to OEM installers. Use in portable exposure conditions
(FCC 2.1093) requires separate equipment authorization.
equipment (FCC section 15.21).
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense (FCC section 15.105).
1.
2.
The modular transmitter must be labelled with its own FCC ID number, and, if the FCC ID is not
visible when the module is installed inside another device, then the outside of the device into
which the module is installed must also display a label referring to the enclosed module. This
exterior label can use wording such as the following:
Example of label required for OEM product containing ZDM-A1281-A2 module
Contains FCC ID: U6TZIGBIT-A2
The enclosed device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (i.) this device may not cause harmful interference and (ii.) this device
must accept any interference received, including interference that may cause undesired
operation.
Example of label required for OEM product containing ZDM-A1281-B0 module
Contains FCC ID: U6TZIGBIT-B0
The enclosed device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (i.) this device may not cause harmful interference and (ii.) this device
must accept any interference received, including interference that may cause undesired
operation.
Any similar wording that expresses the same meaning may be used.
To be used with the ZDM-A1281-B0 module, the external antennas have been tested and
approved which are specified in herebelow.
with other custom design antennas which OEM installer must authorize following the
15.21 requirements.
Zi gBi t™ O EM M odule s
The ZDM-A1281-B0 Module may be integrated
Product Datasheet
Page 18 of 24
FCC