GM-205610-000 DeLorme, GM-205610-000 Datasheet - Page 15

• Manufacturer Part Number: GM-205610-000
• Description: MODULE GPS RCVR GPS2056-10
• Manufacturer: DeLorme

Specifications of GM-205610-000

• Frequency: 1.575GHz
• Data Rate - Maximum: 57.6 kbps
• Modulation Or Protocol: GPS
• Applications: GPS Receiver
• Current - Receiving: 50mA
• Data Interface: PCB, Surface Mount
• Antenna Connector: PCB, Surface Mount
• Voltage - Supply: 3 V ~ 3.6 V
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 40 Pin
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Features: -
• Sensitivity: -
• Memory Size: -
• Other names: GM-205610-000TR

$PSTMADCCAL
Execute an ADC Calibration (using two ADC inputs as reference). Sets the sample frequency and evaluates the ADC
calibration values. To calibrate the ADC, two reference signals have to be supplied: one on the ADC input 2 and the other on
the input 3.
Command: $PSTMADCCAL,<fs>,<ncycles><cr><lf>
Results: $PSTMADCCAL,<ADC_ch2_mean_value>,<
$PSTMADCCALERROR*<checksum><cr><lf> if no success.
$PSTMSTBY
Put the system in standby mode.
Command: $PSTMSTBY,<T><cr><lf>
Results: If success the system goes in standby mode for a T time. If T is zero the system stays in standby mode up to the
hardware wake-up signal. $PSTMSTBYERROR*<checksum><cr><lf> if no success
$PSTMSTOP
Puts the system in stop mode.
Command: $PSTMSTOP,<T><cr><lf>
Results: If success the system goes in stop mode for a T time. After T time the system will be reset.
ecksum><cr><lf> if no success.
$PSTMSRR
Executes a software reset of the system.
Command: $PSTMSRR <cr><lf>
Results: The system will be reset.
$PSTMPIOREAD
Reads a GPIO port
Command: $PSTMPIOREAD ,<port_number><cr><lf>
Results: $PSTMPIOREAD,<port_number>,<value>*<checksum><cr><lf>
Parameter
fs
ncycles
Parameter
ADC_ch2_mean_value
ADC_ch3_mean_value
fs
ncycles
checksum
Parameter
T
Parameter
T
Parameter
port_number
Parameter
port_number
value
checksum
Format
%d
%d
Format
%05d
Format
%05d
Format
%1d
Format
%1d
%08x
%02x
Format
%03x
%03x
%d
%d
%02x
Description
ADC Sample Frequency
Number of cycles to perform the calibration.
Description
Standby period (seconds). If T is 0 then the system goes in standby mode for
undefined time and can be awakened by hardware.
Description
Stop period (seconds).
Description
Port to be read
Description
Port
Value read on the port (hexadecimal value)
Checksum of the message bytes without *<checksum><cr><lf> characters.
Description
ADC channel 2 average value ( 0x0 .. 0x800 )
ADC channel 3 average value ( 0x0 .. 0x800 )
Sample frequency
Number of cycles on which the calibration has been performed.
Checksum of the message bytes without *<checksum><cr><lf> characters.
ADC_ch3_mean_value
>,<fs> ,<ncycles>*<checksum><cr><lf>
$PSTMSTOPERROR*<ch
Page 15