XBP09-DMDK Digi International, XBP09-DMDK Datasheet - Page 7

• Manufacturer Part Number: XBP09-DMDK
• Description: KIT STARTER PROMESH XBEE PRO
• Manufacturer: Digi International
• Series: XBEE-PRO™r
• Type: Transceiver, XBeePror

Specifications of XBP09-DMDK

• Frequency: 900MHz
• Wireless Frequency: 900 MHz
• Interface Type: RS-232, USB, UART
• Modulation: FHSS
• Security: 128 bit AES
• Operating Voltage: 3.3 V
• Output Power: 50 mW
• Antenna: RPSMA
• For Use With/related Products: Xbee-PRO Modules
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: 602-1130

XBee‐PRO® 900 OEM RF Modules
Pin #
10
11
12
13
14
15
16
17
18
19
20
1
2
3
4
5
6
7
8
9
Pin Signals
DTR / SLEEP_RQ/ DIO8
PWM0 / RSSI / DIO10
Associate / DIO5/AD5
DIN / CONFIG
PWM / DIO11
ON / SLEEP
CTS / DIO7
RTS / DIO6
AD3 / DIO3
AD2 / DIO2
AD1 / DIO1
AD0 / DIO0
DIO4/AD4
[reserved]
RESET
Name
DIO12
DOUT
GND
Vref
Vcc
XBee‐PRO® 900 RF Module Pin Number
(top sides shown ‐ shields on bottom)
Pin Assignments for the XBee‐PRO® 900 Modules
Design Notes:
To ensure proper power up, Vcc SLOPE must be superior or equal to 6V/ms.
© 2008 Digi International, Inc.
• Minimum connections: VCC, GND, DOUT & DIN
• Minimum connections to support serial firmware upgrades: VCC, GND, DIN, DOUT, RTS & DTR
• Signal Direction is specified with respect to the module
• Module includes an internal 5K Ohm resistor to RESET
• Several of the input pull-ups can be configured using the PR command
• Unused pins should be left disconnected
Input/Open drain
(Low‐asserted signals are distinguished with a horizontal line above signal name.)
Direction
Output
Output
output
Either
Either
Either
Either
Either
Either
Either
Either
Either
Either
Either
Either
Input
-
-
-
-
This line must be connected if AD sampling is desired. Must be
Module Reset (reset pulse must be at least 100 us. This must
line low when a reset occurs. This line should never be driven
be driven as a open drain/collector. The module will drive this
PWM Output 0 / RX Signal Strength Indicator / Digital IO
Clear-to-Send Flow Control or Digital I/O 7
Request-to-Send Flow Control, Digital I/O
Module Status Indicator or Digital I/O 9
Pin Sleep Control Line or Digital IO 8
Associated Indicator, Digital I/O 5
Analog Input 3 or Digital I/O 3
Analog Input 2 or Digital I/O 2
Analog Input 1 or Digital I/O 1
Analog Input 0, Digital I/O 0
between 2.6 V and Vcc.
UART Data Out
Do not connect
Description
UART Data In
Power supply
Digital I/O 12
Digital I/O 11
Digital I/O 4
Ground
high.)
Max Voltage
3.6V
Vcc
Vcc
Vcc
Vcc
Vcc
Vcc
Vcc
Vcc
n/a
Vcc
Vcc
Vcc
Vcc
Vcc
5V
5V
0V
5V
Vcc
7