XBP09-DMDK Digi International, XBP09-DMDK Datasheet - Page 23

• Manufacturer Part Number: XBP09-DMDK
• Description: KIT STARTER PROMESH XBEE PRO
• Manufacturer: Digi International
• Series: XBEE-PRO™r
• Type: Transceiver, XBeePror

Specifications of XBP09-DMDK

• Frequency: 900MHz
• Wireless Frequency: 900 MHz
• Interface Type: RS-232, USB, UART
• Modulation: FHSS
• Security: 128 bit AES
• Operating Voltage: 3.3 V
• Output Power: 50 mW
• Antenna: RPSMA
• For Use With/related Products: Xbee-PRO Modules
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: 602-1130

Diagnostics Commands
AT Command Options
AT Command Options Commands
Node Identification Commands
XBee‐PRO® 900 OEM RF Modules
AT
Command
RP
TR
TP
%V
AT
Command
CT
CN
GT
CC
AT
Command
ID
NT
NI
DN
Name and Description
RSSI PWM timer Set or read the time that the RSSI output (indicating signal strength)
will remain active after the last reception. Time units are measured in tenths of seconds
Transmission Errors Read the number of MAC frames that exhaust MAC retries
without ever receiving a MAC acknowledgement message from the adjacent node.
When the value reaches 0xffff, it stays there.
Temperature Read module temperature in Celsius. Negatives temperatures can be
returned.
Supply Voltage. Reads the voltage on the Vcc pin in mV. Should be read module
voltage in milivolts.
Name and Description
Command Mode Timeout. Set/Read the period of inactivity (no valid commands
received) after which the RF module automatically exits AT Command Mode and returns
to Idle Mode.
Exit Command Mode. Explicitly exit the module from AT Command Mode.
Guard Times. Set required period of silence before and after the Command Sequence
Characters of the AT Command Mode Sequence (GT + CC + GT). The period of silence
is used to prevent inadvertent entrance into AT Command Mode.
Command Character. Set or read the character to be used between guard times of the
AT Command Mode Sequence. The AT Command Mode Sequence causes the radio
modem to enter Command Mode (from Idle Mode).
Name and Description
PAN ID. Set or read the user network address. Nodes must have the same network
address to communicate. Changes to ID should be written to non-volatile memory using
the WR command.
Node Discover Timeout. Set/Read the amount of time a node will spend discovering
other nodes when ND or DN is issued.
Node Identifier. Stores a string identifier. The string accepts only printable ASCII data
In AT Command Mode, the string can not start with a space. A Carriage return ends the
command. Command will automatically end when maximum bytes for the string have
been entered. This string is returned as part of the ATND (Network Discover) command.
This identifier is also used with the ATDN (Destination Node) command. .
Discover Node - Destination Node. Resolves an NI (Node Identifier) string to a
physical address (casesensitive).
The following events occur after the destination node is discovered:
(Node Identifier) string.
The 16-bit network and 64-bit extended addresses are returned in an API Command
Response frame.
If there is no response from a module within (NT * 100) milliseconds or a parameter is
not specified (left blank), the command is terminated and an “ERROR” message is
returned. In the case of an ERROR, Command Mode is not exited.
1. DL & DH are set to the extended (64-bit) address of the module with the matching NI
<AT Firmware>
2. OK (or ERROR)\r is returned.
3. Command Mode is exited to allow immediate communication
<API Firmware>
Node Identification
© 2008 Digi International, Inc.
Parameter Range
0x0000 to 0x7FFF
0 - 0xFC
[x 100 msec]
up to 20 byte ASCII string a space character
20 byte ascii string
Parameter Range
1 to 0xff
n/a
0xff74 to 0x0258
-0-0x/F00
Parameter Range
0XFFF w VPDG
--
0 to 0xFFFF
0 - 0xFF
Default
0x20 = 3.2
seconds
n/a
n/a
n/a
Default
0x64 (100d)
--
0x3E8
(1000d)
0x2B
Default
0x7FFF
0x82 (130d)
23