XBP09-DMDK Digi International, XBP09-DMDK Datasheet - Page 20

• Manufacturer Part Number: XBP09-DMDK
• Description: KIT STARTER PROMESH XBEE PRO
• Manufacturer: Digi International
• Series: XBEE-PRO™r
• Type: Transceiver, XBeePror

Specifications of XBP09-DMDK

• Frequency: 900MHz
• Wireless Frequency: 900 MHz
• Interface Type: RS-232, USB, UART
• Modulation: FHSS
• Security: 128 bit AES
• Operating Voltage: 3.3 V
• Output Power: 50 mW
• Antenna: RPSMA
• For Use With/related Products: Xbee-PRO Modules
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: 602-1130

Special
Addressing
Addressing Commands)
Serial Interfacing (I/O)
Serial Interfacing Commands
AT
Command
DH
DL
SH
SL
NI
AT
Command
AP
AO
BD
RO
4. 900/DigiMesh Command Reference Tables
Special Commands
AT
Command
WR
RE
FR
AC
R1
VL
Name and Description
Destination Address High. Set/Get the upper 32 bits of the 64-bit destination address.
When combined with DL, it defines the destination address used for transmission.
Destination Address Low. Set/Get the lower 32 bits of the 64-bit destination address.
When combined with DH, DL defines the destination address used for transmission.
Serial Number High. Read high 32 bits of the RF module's unique IEEE 64-bit
address. 64-bit source address is always enabled. This value is read-only and it never
changes
Serial Number Low. Read low 32 bits of the RF module's unique IEEE 64-bit address.
64-bit source address is always enabled . This is read only and it is also the serial
number of the node. .
Node Identifier. Stores a string identifier. The register only accepts printable ASCII
data. In AT Command Mode, a string can not start with a space. A carriage return ends
the command. Command will automatically end when maximum bytes for the string
have been entered. This string is returned as part of the ND (Node Discover) command.
This identifier is also used with the DN (Destination Node) command.
Name and Description
API mode. Set or read the API mode of the radio. The following settings are allowed:
0 API mode is off. All UART input and output is raw data and packets are delineated
using the RO and RB parameters.
1 API mode is on. All UART input and output data is packetized in the API format,
without escape sequences.
2 API mode is on with escaped sequences inserted to allow for control characters (XON,
XOFF, escape, and the 0x7e delimiter to be passed as data.
API Output Format. Enables different API output frames. Options include:
0 Standard Data Frames (0x90 for RF rx)
1 Explicit Addressing Data Frames (0x91 for RF rx)
Baud rate. Set or read serial interface rate (speed for data transfer between radio
modem and host). Values from 0-8 select preset standard rates. Values at 0x39 and
above select the actual baud rate. Providing the host supports it. Baud rates can go as
high as 1.875Mbps. The values from 0 to 8 are interpreted as follows:
Packetization Timeout. Set/Read number of character times of inter-character silence
required before packetization. Set (RO=0) to transmit characters as they arrive instead of
buffering them into one RF packet.
0 - 1,200bps
1 - 2,400bps
2 - 4,800bps
Name and Description
Write. Write parameter values to non-volatile memory so that parameter modifications
persist through subsequent resets.
Note: Once WR is issued, no additional characters should be sent to the module until
after the "OK\r" response is received.
Restore Defaults. Restore module parameters to factory defaults.
Software Reset. Reset module. Responds immediately with an “OK” then performs a
reset 100ms later.
Apply Changes. Immediately applies new settings without exiting command mode.
Restore Compiled. Restore module parameters to compiled defaults.
Version Long. Shows detailed version information including application build date and
time.
3 - 9,600bps
4 - 19,200bps
5 - 38,400bps
© 2008 Digi International, Inc.
6 - 57,600bps
7 - 115,200bps
8 - 230,400bps
Parameter Range
0 to 0xFFFFFFFF
0 to 0xFFFFFFFF
0x-0xFFFFFFFF
0 to 0xFFFFFFFF
20-Byte printable
ASCII string
Parameter Range
0, 1, or 2
0, 1
0 to 8, and 0x39 to
0x1c9c38
0 - 0xFF
[x character times]
Parameter Range Default
--
--
--
--
--
--
Default
0
0
0x03 (9600
bps)
3
Default
0
0x0000FFFF
Factory
Factory
Space Character
--
--
--
--
--
--
20