XBP09-DMDK Digi International, XBP09-DMDK Datasheet - Page 36

• Manufacturer Part Number: XBP09-DMDK
• Description: KIT STARTER PROMESH XBEE PRO
• Manufacturer: Digi International
• Series: XBEE-PRO™r
• Type: Transceiver, XBeePror

Specifications of XBP09-DMDK

• Frequency: 900MHz
• Wireless Frequency: 900 MHz
• Interface Type: RS-232, USB, UART
• Modulation: FHSS
• Security: 128 bit AES
• Operating Voltage: 3.3 V
• Output Power: 50 mW
• Antenna: RPSMA
• For Use With/related Products: Xbee-PRO Modules
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: 602-1130

Appendix B: Agency Certifications
United States FCC
OEM Labeling Requirements
FCC Notices
FCC-Approved Antennas (900 MHz)
The XBee-PRO® 900 RF Module complies with Part 15 of the FCC rules and regulations.
Compliance with the labeling requirements, FCC notices and antenna usage guidelines is required.
To fufill FCC Certification, the OEM must comply with the following regulations:
Required FCC Label for OEM products containing the XBee-PRO® 900 RF Module
IMPORTANT: The XBee-PRO® 900 OEM RF Module has been certified by the FCC for use with
other products without any further certification (as per FCC section 2.1091). Modifications not
expressly approved by Digi could void the user's authority to operate the equipment.
IMPORTANT: OEMs must test final product to comply with unintentional radiators (FCC section
15.107 & 15.109) before declaring compliance of their final product to Part 15 of the FCC Rules.
IMPORTANT: The RF module has been certified for remote and base radio applications. If the
module will be used for portable applications, the device must undergo SAR testing.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures: Re-orient or relocate the receiving
antenna, Increase the separation between the equipment and receiver, Connect equipment and
receiver to outlets on different circuits, or consult the dealer or an experienced radio/TV technician
for help.
The XBee-PRO® 900 RF Module can be installed utilizing antennas and cables constructed with
standard connectors (Type-N, SMA, TNC, etc.) if the installation is performed professionally and
according to FCC guidelines. For installations not performed by a professional, non-standard
connectors (RPSMA, RPTNC, etc.) must be used.
The modules are FCC approved for fixed base station and mobile applications. If the antenna is
mounted at least 20cm (8 in.) from nearby persons, the application is considered a mobile
application. Antennas not listed in the table must be tested to comply with FCC Section 15.203
(Unique Antenna Connectors) and Section 15.247 (Emissions).
Contains FCC ID:MCQ-XBEE09P
The enclosed device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (i.) this device may not cause harmful interference and (ii.) this device must accept any
interference received, including interference that may cause undesired operation.
1.
2.
© 2008 Digi International, Inc.
The system integrator must ensure that the text on the external label provided with this
device is placed on the outside of the final product. [Figure A-01]
XBee-PRO® 900 RF Module may only be used with antennas that have been tested and
approved for use with this module [refer to the antenna tables in this section].
WARNING: The Original Equipment Manufacturer (OEM) must ensure that FCC labeling
requirements are met. This includes a clearly visible label on the outside of the final
product enclosure that displays the contents shown in the figure below.
36