C8051F020 Silicon Laboratories Inc, C8051F020 Datasheet - Page 146
![no-image](/images/manufacturer_photos/0/6/609/silicon_laboratories_inc_sml.jpg)
C8051F020
Manufacturer Part Number
C8051F020
Description
IC 8051 MCU 64K FLASH 100TQFP
Manufacturer
Silicon Laboratories Inc
Series
C8051F02xr
Specifications of C8051F020
Core Processor
8051
Core Size
8-Bit
Speed
25MHz
Connectivity
EBI/EMI, SMBus (2-Wire/I²C), SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
Number Of I /o
64
Program Memory Size
64KB (64K x 8)
Program Memory Type
FLASH
Ram Size
4.25K x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 3.6 V
Data Converters
A/D 8x8b, 8x12b; D/A 2x12b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
100-TQFP, 100-VQFP
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Eeprom Size
-
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
C8051F020
Manufacturer:
SILICON
Quantity:
2
Company:
Part Number:
C8051F020
Manufacturer:
Silicon Laboratories Inc
Quantity:
10 000
Part Number:
C8051F020
Manufacturer:
CYPRESS/赛普拉斯
Quantity:
20 000
Company:
Part Number:
C8051F020-GQ
Manufacturer:
SiliconL
Quantity:
4 035
Company:
Part Number:
C8051F020-GQ
Manufacturer:
MICRON
Quantity:
200
Company:
Part Number:
C8051F020-GQ
Manufacturer:
Silicon Laboratories Inc
Quantity:
10 000
Company:
Part Number:
C8051F020-GQR
Manufacturer:
SILICON
Quantity:
3 000
Company:
Part Number:
C8051F020-GQR
Manufacturer:
Silicon Laboratories Inc
Quantity:
10 000
Part Number:
C8051F020-GQR
Manufacturer:
SIL
Quantity:
20 000
Company:
Part Number:
C8051F020DK
Manufacturer:
SiliconL
Quantity:
10
Company:
Part Number:
C8051F020R
Manufacturer:
Silicon Laboratories Inc
Quantity:
10 000
C8051F020/1/2/3
16.2. Configuring the External Memory Interface
Configuring the External Memory Interface consists of four steps:
Each of these four steps is explained in detail in the following sections. The Port selection, Multiplexed mode selec-
tion, and Mode bits are located in the EMI0CF register shown in Figure 16.2.
16.3. Port Selection and Configuration
The External Memory Interface can appear on Ports 3, 2, 1, and 0 (C8051F020/1/2/3 devices) or on Ports 7, 6, 5, and
4 (C8051F020/2 devices only), depending on the state of the PRTSEL bit (EMI0CF.5). If the lower Ports are selected,
the EMIFLE bit (XBR2.1) must be set to a ‘1’ so that the Crossbar will skip over P0.7 (/WR), P0.6 (/RD), and if mul-
tiplexed mode is selected P0.5 (ALE). For more information about the configuring the Crossbar, see
“17. PORT INPUT/OUTPUT” on page
The External Memory Interface claims the associated Port pins for memory operations ONLY during the execution of
an off-chip MOVX instruction. Once the MOVX instruction has completed, control of the Port pins reverts to the Port
latches or to the Crossbar (on Ports 3, 2, 1, and 0). See
more information about the Crossbar and Port operation and configuration. The Port latches should be explicitly
configured to ‘park’ the External Memory Interface pins in a dormant state, most commonly by setting them
to a logic 1.
During the execution of the MOVX instruction, the External Memory Interface will explicitly disable the drivers on
all Port pins that are acting as Inputs (Data[7:0] during a READ operation, for example). The Output mode of the Port
pins (whether the pin is configured as Open-Drain or Push-Pull) is unaffected by the External Memory Interface oper-
ation, and remains controlled by the PnMDOUT registers. See
for more information about Port output mode configuration.
146
1.
2.
3.
off-chip only).
4.
5.
Select EMIF on Low Ports (P3, P2, P1, and P0) or High Ports (P7, P6, P5, and P4).
Select Multiplexed mode or Non-multiplexed mode.
Select the memory mode (on-chip only, split mode without bank select, split mode with bank select, or
Set up timing to interface with off-chip memory or peripherals.
Select the desired output mode for the associated Ports (registers PnMDOUT, P74OUT).
161.
Rev. 1.4
Section “17. PORT INPUT/OUTPUT” on page 161
Section “17. PORT INPUT/OUTPUT” on page 161
Section
for