ACE1101BEMT8X Fairchild Semiconductor, ACE1101BEMT8X Datasheet - Page 30
![no-image](/images/manufacturer_photos/0/2/252/fairchild_semiconductor_sml.jpg)
ACE1101BEMT8X
Manufacturer Part Number
ACE1101BEMT8X
Description
IC MCU 1KBIT EEPROM 8TSSOP
Manufacturer
Fairchild Semiconductor
Series
ACEX® 11xxr
Datasheet
1.ACE1101BEMT8.pdf
(35 pages)
Specifications of ACE1101BEMT8X
Core Processor
ACE1001
Core Size
8-Bit
Speed
4MHz
Peripherals
Brown-out Detect/Reset, LVD, POR, PWM, WDT
Number Of I /o
6
Program Memory Size
1KB (1K x 8)
Program Memory Type
EEPROM
Eeprom Size
64 x 8
Ram Size
64 x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 5.5 V
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
8-TSSOP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Data Converters
-
Connectivity
-
ACE1101 Product Family Rev. B.2
The HALT mode is a power saving feature that almost completely
shuts down the device for current conservation. The device is
placed into HALT mode by setting the HALT enable bit (EHALT)
of the HALT register through software using only the “LD M, #”
instruction. EHALT is a write only bit and is automatically cleared
upon exiting HALT. When entering HALT, the internal oscillator
and all the on-chip systems including the LBD and the BOR
circuits are shut down.
The device can exit HALT mode only by the MIW circuit. There-
fore, prior to entering HALT mode, software must configure the
MIW circuit accordingly. (See Section 8) After a wakeup from
HALT, a 1ms start-up delay is initiated to allow the internal
oscillator to stabilize before normal execution resumes. Immedi-
ately after exiting HALT, software must clear the Power Mode
Clear (PMC) register by only using the “LD M, #” instruction. (See
Figure 30)
undefined
Bit 7
Multi-Input
Wakeup
undefined
Bit 6
LD HALT, #01h
LD PMC, #00h
Normal Mode
Normal Mode
Resume
Halt
33pF
a)
undefined
Bit 5
(G1)
CKI
1M
CKO
(G0)
undefined
33pF
Bit 4
b)
In addition to the HALT mode power saving feature, the device
also supports an IDLE mode operation. The device is placed into
IDLE mode by setting the IDLE enable bit (EIDLE) of the HALT
register through software using only the “LD M, #” instruction.
EIDLE is a write only bit and is automatically cleared upon exiting
IDLE. The IDLE mode operation is similar to HALT except the
internal oscillator, the Watchdog, and the Timer 0 remain active
while the other on-chip systems including the LBD and the BOR
circuits are shut down.
The device can exit IDLE by a Timer 0 overflow every 8192 cycles
or/and by the MIW circuit. If exiting IDLE mode with the MIW, prior
to entering, software must configure the MIW circuit accordingly.
(See Section 8) Once a wake from IDLE mode is triggered, the
core will begin normal operation by the next clock cycle. Immedi-
ately after exiting IDLE mode, software must clear the Power
Mode Clear (PMC) register by using only the “LD M, #” instruction.
(See Figure 31)
undefined
C
Bit 3
(G1)
CKI
R
Multi-Input
Underflow
Wakeup
Timer0
CKO
(G0)
undefined
Bit 2
V
LD
LD
CC
Resume Normal
Normal Mode
IDLE Mode
PMC, #00H
Mode
HALT, #01H
EIDLE
Bit 1
www.fairchildsemi.com
EHALT
Bit 0