DSPIC30F2010-30I/SO Microchip Technology, DSPIC30F2010-30I/SO Datasheet - Page 129

• Manufacturer Part Number: DSPIC30F2010-30I/SO
• Description: IC DSPIC MCU/DSP 12K 28SOIC
• Manufacturer: Microchip Technology
• Series: dsPIC™ 30Fr

Specifications of DSPIC30F2010-30I/SO

• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 30 MIPs
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, Motor Control PWM, QEI, POR, PWM, WDT
• Number Of I /o: 20
• Program Memory Size: 12KB (4K x 24)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.5 V ~ 5.5 V
• Data Converters: A/D 6x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-SOIC (7.5mm Width)
• Core Frequency: 40MHz
• Core Supply Voltage: 5.5V
• Embedded Interface Type: I2C, SPI, UART
• No. Of I/o's: 20
• Flash Memory Size: 12KB
• Supply Voltage Range: 2.5V To 5.5V
• Package: 28SOIC W
• Device Core: dsPIC
• Family Name: dsPIC30
• Maximum Speed: 30 MHz
• Operating Supply Voltage: 3.3|5 V
• Data Bus Width: 16 Bit
• Number Of Programmable I/os: 20
• Interface Type: I2C/SPI/UART
• On-chip Adc: 6-chx10-bit
• Number Of Timers: 3
• Lead Free Status / RoHS Status: Request inventory verification / Request inventory verification

19.3
The dsPIC30F2010 differentiates between various
kinds of Reset:
a)
b)
c)
d)
e)
f)
g)
h)
FIGURE 19-2:
19.3.1
A power-on event will generate an internal POR pulse
when a V
at the POR circuit threshold voltage (V
nominally 1.85V. The device supply voltage character-
istics must meet specified starting voltage and rise rate
requirements. The POR pulse will Reset a POR timer
and place the device in the Reset state. The POR also
selects the device clock source identified by the
© 2008 Microchip Technology Inc.
oscillator configuration fuses.
Power-on Reset (POR)
MCLR Reset during normal operation
MCLR Reset during Sleep
Watchdog Timer (WDT) Reset (during normal
operation)
Programmable Brown-out Reset (BOR)
RESET Instruction
Reset cause by trap lockup (TRAPR)
Reset caused by illegal opcode, or by using an
uninitialized W register as an Address Pointer
(IOPUWR)
MCLR
V
DD
Illegal Opcode/
Uninitialized W Register
Reset
DD
Instruction
RESET
POR: POWER-ON RESET
rise is detected. The Reset pulse will occur
Trap Conflict
Brown-out
V
Sleep or Idle
Module
Detect
DD
WDT
Reset
RESET SYSTEM BLOCK DIAGRAM
Rise
BOREN
Glitch Filter
Digital
POR
POR
), which is
BOR
Different registers are affected in different ways by
various Reset conditions. Most registers are not
affected by a WDT wake-up, since this is viewed as the
resumption of normal operation. Status bits from the
RCON register are set or cleared differently in different
Reset situations, as indicated in Table 19-5. These bits
are used in software to determine the nature of the
Reset.
A block diagram of the on-chip Reset circuit is shown in
Figure 19-2.
A MCLR noise filter is provided in the MCLR Reset
path. The filter detects and ignores small pulses.
Internally generated Resets do not drive MCLR pin low.
The POR circuit inserts a small delay, T
nominally 10 μs and ensures that the device bias
circuits are stable. Furthermore, a user selected
power-up time-out (T
parameter is based on device Configuration bits and
can be 0 ms (no delay), 4 ms, 16 ms, or 64 ms. The
total delay is at device power-up T
these delays have expired, SYSRST will be negated on
the next leading edge of the Q1 clock, and the PC will
jump to the Reset vector.
The timing for the SYSRST signal is shown in
Figure 19-3 through Figure 19-5.
dsPIC30F2010
S
R
PWRT
) is applied. The T
Q
POR
DS70118H-page 129
+ T
SYSRST
POR
PWRT
, which is
. When
PWRT