UPD78F0555MA-FAA-AX Renesas Electronics America, UPD78F0555MA-FAA-AX Datasheet - Page 539
UPD78F0555MA-FAA-AX
Manufacturer Part Number
UPD78F0555MA-FAA-AX
Description
MCU 8BIT 16-SSOP
Manufacturer
Renesas Electronics America
Series
78K0/Kx2-Lr
Datasheet
1.UPD78F0551MA-FAA-AX.pdf
(822 pages)
Specifications of UPD78F0555MA-FAA-AX
Core Processor
78K/0
Core Size
8-Bit
Speed
10MHz
Connectivity
I²C, LIN, UART/USART
Peripherals
LVD, POR, PWM, WDT
Number Of I /o
9
Program Memory Size
4KB (4K x 8)
Program Memory Type
FLASH
Ram Size
384 x 8
Voltage - Supply (vcc/vdd)
1.8 V ~ 5.5 V
Data Converters
A/D 4x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
*
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
- Current page: 539 of 822
- Download datasheet (6Mb)
78K0/Kx2-L
15.5.15 Cautions
R01UH0028EJ0400 Rev.4.00
Sep 27, 2010
(1) When STCEN (bit 1 of IICA flag register 0 (IICAF0)) = 0
(2) When STCEN = 1
(3) If other I
(4) Setting the STT0 and SPT0 bits (bits 1 and 0 of the IICACTL0 register) again after they are set and before they are
(5) When transmission is reserved, set SPIE0 (bit 4 of the IICACTL0 register) to 1 so that an interrupt request is
Immediately after I
IICAF0 register) = 1) is recognized regardless of the actual bus status. When changing from a mode in which no
stop condition has been detected to a master device communication mode, first generate a stop condition to
release the bus, then perform master device communication.
When using multiple masters, it is not possible to perform master device communication when the bus has not
been released (when a stop condition has not been detected).
Use the following sequence for generating a stop condition.
<1> Set IICA control register 1 (IICACTL1).
<2> Set bit 7 (IICE0) of IICA control register 0 (IICACTL0) to 1.
<3> Set bit 0 (SPT0) of IICACTL0 to 1.
Immediately after I
regardless of the actual bus status. To generate the first start condition (STT0 (bit 1 of the IICA control register 0
(IICACTL0)) = 1), it is necessary to confirm that the bus has been released, so as to not disturb other
communications.
If I
low and the SCLA0 pin is high, the macro of I
condition). If the value on the bus at this time can be recognized as an extension code, ACK is returned, but this
interferes with other I
<1> Clear bit 4 (SPIE0) of the IICACTL0 register to 0 to disable generation of an interrupt request signal
<2> Set bit 7 (IICE0) of the IICACTL0 register to 1 to enable the operation of I
<3> Wait for detection of the start condition.
<4> Set bit 6 (LREL0) of the IICACTL0 register to 1 before ACK is returned (4 to 80 clocks after setting the IICE0
cleared to 0 is prohibited.
generated when the stop condition is detected. Transfer is started when communication data is written to the IICA
shift register (IICA) after the interrupt request is generated. Unless the interrupt is generated when the stop
condition is detected, the device stops in the wait state because the interrupt request is not generated when
communication is started. However, it is not necessary to set the SPIE0 bit to 1 when the MSTS0 bit (bit 7 of the
IICA status register (IICAS0)) is detected by software.
2
C operation is enabled and the device participates in communication already in progress when the SDAA0 pin is
(INTIICA0) when the stop condition is detected.
bit to 1), to forcibly disable detection.
2
C communications are already in progress
2
C operation is enabled (IICE0 = 1), the bus communication status (the IICBSY flag (bit 6 of the
2
C operation is enabled (IICE0 = 1), the bus released status (IICBSY = 0) is recognized
2
C communications. To avoid this, start I
2
C recognizes that the SDAA0 pin has gone low (detects a start
2
C in the following sequence.
CHAPTER 15 SERIAL INTERFACE IICA
2
C.
525
Related parts for UPD78F0555MA-FAA-AX
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
KIT STARTER FOR M16C/29
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C/2D
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
R0K33062P STARTER KIT
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C/23 E8A
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C/25
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER H8S2456 SHARPE DSPLY
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C38C
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C35C
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8CL3AC+LCD APPS
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR RX610
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R32C/118
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT DEV RSK-R8C/26-29
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR SH7124
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR H8SX/1622
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT DEV FOR SH7203
Manufacturer:
Renesas Electronics America
Datasheet: