M38588GCSP#U0 Renesas Electronics America, M38588GCSP#U0 Datasheet - Page 10

• Manufacturer Part Number: M38588GCSP#U0
• Description: IC 740/3858 MCU QZ-ROM 42DIP
• Manufacturer: Renesas Electronics America
• Series: 740/38000r

Specifications of M38588GCSP#U0

• Core Processor: 740
• Core Size: 8-Bit
• Speed: 12.5MHz
• Connectivity: SIO, UART/USART
• Peripherals: PWM, WDT
• Number Of I /o: 34
• Program Memory Size: 48KB (48K x 8)
• Program Memory Type: QzROM
• Ram Size: 1.5K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 9x8b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 85°C
• Package / Case: 42-DIP (0.600", 15.24mm)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

3858 Group
[Processor status register (PS)]
The processor status register is an 8-bit register consisting of 5
flags which indicate the status of the processor after an arithmetic
operation and 3 flags which decide MCU operation. Branch opera-
tions can be performed by testing the Carry (C) flag , Zero (Z) flag,
Overflow (V) flag, or the Negative (N) flag. In decimal mode, the Z,
V, N flags are not valid.
•Bit 0: Carry flag (C)
•Bit 1: Zero flag (Z)
•Bit 2: Interrupt disable flag (I)
•Bit 3: Decimal mode flag (D)
Table 4 Set and clear instructions of each bit of processor status register
REJ03B0139-0111
page 8 of 73
Set instruction
Clear instruction
The C flag contains a carry or borrow generated by the arithmetic
logic unit (ALU) immediately after an arithmetic operation. It can
also be changed by a shift or rotate instruction.
The Z flag is set if the result of an immediate arithmetic operation
or a data transfer is “0”, and cleared if the result is anything other
than “0”.
The I flag disables all interrupts except for the interrupt
generated by the BRK instruction.
Interrupts are disabled when the I flag is “1”.
The D flag determines whether additions and subtractions are
executed in binary or decimal. Binary arithmetic is executed when
this flag is “0”; decimal arithmetic is executed when it is “1”.
Decimal correction is automatic in decimal mode. Only the ADC
and SBC instructions can be used for decimal arithmetic.
Rev.1.11
Dec 18, 2008
C flag
SEC
CLC
Z flag
_
_
I flag
SEI
CLI
•Bit 4: Break flag (B)
•Bit 5: Index X mode flag (T)
•Bit 6: Overflow flag (V)
•Bit 7: Negative flag (N)
The B flag is used to indicate that the current interrupt was
generated by the BRK instruction. The BRK flag in the processor
status register is always “0”. When the BRK instruction is used to
generate an interrupt, the processor status register is pushed
onto the stack with the break flag set to “1”.
When the T flag is “0”, arithmetic operations are performed
between accumulator and memory. When the T flag is “1”, direct
arithmetic operations and direct data transfers are enabled
between memory locations.
The V flag is used during the addition or subtraction of one byte
of signed data. It is set if the result exceeds +127 to -128. When
the BIT instruction is executed, bit 6 of the memory location
operated on by the BIT instruction is stored in the overflow flag.
The N flag is set if the result of an arithmetic operation or data
transfer is negative. When the BIT instruction is executed, bit 7 of
the memory location operated on by the BIT instruction is stored
in the negative flag.
SED
D flag
CLD
B flag
_
_
T flag
SET
CLT
V flag
CLV
_
N flag
_
_