MC908GR4CDWE Freescale Semiconductor, MC908GR4CDWE Datasheet - Page 222

• Manufacturer Part Number: MC908GR4CDWE
• Description: IC MCU 4K FLASH 8MHZ 28-SOIC
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908GR4CDWE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SCI, SPI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 17
• Program Memory Size: 4KB (4K x 8)
• Program Memory Type: FLASH
• Ram Size: 384 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 6x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-SOIC (7.5mm Width)
• Controller Family/series: HC08
• No. Of I/o's: 21
• Ram Memory Size: 384Byte
• Cpu Speed: 8MHz
• No. Of Timers: 1
• Embedded Interface Type: I2C, SCI, SPI
• Rohs Compliant: Yes
• Processor Series: HC08GR
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 384 B
• Interface Type: SCI, SPI
• Maximum Clock Frequency: 8.2 MHz
• Number Of Programmable I/os: 21
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, DEMO908GZ60E, M68CBL05CE, M68EML08GPGTE
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8 bit, 6 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

Serial Peripheral Interface (SPI)
SPWOM — SPI Wired-OR Mode Bit
SPE — SPI Enable
SPTIE— SPI Transmit Interrupt Enable
20.13.2 SPI Status and Control Register
The SPI status and control register contains flags to signal these conditions:
The SPI status and control register also contains bits that perform these functions:
SPRF — SPI Receiver Full Bit
ERRIE — Error Interrupt Enable Bit
222
This read/write bit disables the pullup devices on pins SPSCK, MOSI, and MISO so that those pins
become open-drain outputs.
This read/write bit enables the SPI module. Clearing SPE causes a partial reset of the SPI. See
Resetting the
This read/write bit enables CPU interrupt requests generated by the SPTE bit. SPTE is set when a byte
transfers from the transmit data register to the shift register. Reset clears the SPTIE bit.
•
•
•
•
•
•
•
This clearable, read-only flag is set each time a byte transfers from the shift register to the receive data
register. SPRF generates a CPU interrupt request if the SPRIE bit in the SPI control register is set also.
During an SPRF CPU interrupt, the CPU clears SPRF by reading the SPI status and control register
with SPRF set and then reading the SPI data register. Reset clears the SPRF bit.
This read/write bit enables the MODF and OVRF bits to generate CPU interrupt requests. Reset clears
the ERRIE bit.
1 = Wired-OR SPSCK, MOSI, and MISO pins
0 = Normal push-pull SPSCK, MOSI, and MISO pins
1 = SPI module enabled
0 = SPI module disabled
1 = SPTE CPU interrupt requests enabled
0 = SPTE CPU interrupt requests disabled
1 = Receive data register full
0 = Receive data register not full
1 = MODF and OVRF can generate CPU interrupt requests
0 = MODF and OVRF cannot generate CPU interrupt requests
Receive data register full
Failure to clear SPRF bit before next byte is received (overflow error)
Inconsistent logic level on SS pin (mode fault error)
Transmit data register empty
Enable error interrupts
Enable mode fault error detection
Select master SPI baud rate
Address: $0011
Reset:
Read:
Write:
SPI. Reset clears the SPE bit.
Figure 20-14. SPI Status and Control Register (SPSCR)
SPRF
Bit 7
0
MC68HC908GR8 • MC68HC908GR4 Data Sheet, Rev. 7
= Unimplemented
ERRIE
6
0
OVRF
5
0
MODF
4
0
SPTE
3
1
MODFEN
2
0
SPR1
1
0
Freescale Semiconductor
SPR0
Bit 0
0
20.9