MC9S08RD32PE Freescale Semiconductor, MC9S08RD32PE Datasheet - Page 65

• Manufacturer Part Number: MC9S08RD32PE
• Description: IC MCU 32K FLASH 2K RAM 28-DIP
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of MC9S08RD32PE

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SCI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 23
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Oscillator Type: Internal
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 28-DIP (0.600", 15.24mm)
• Processor Series: S08RD
• Core: HCS08
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Interface Type: SCI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 39
• Number Of Timers: 2
• Operating Supply Voltage: 1.8 V to 3.6 V
• Maximum Operating Temperature: + 70 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: EWS08
• Development Tools By Supplier: DEMO9S08RG60E
• Minimum Operating Temperature: 0 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

5.8.2
This register includes six read-only status flags to indicate the source of the most recent reset. When a
debug host forces reset by writing 1 to BDFR in the SBDFR register, none of the status bits in SRS will be
set. Writing any value to this register address clears the COP watchdog timer without affecting the contents
of this register. The reset state of these bits depends on what caused the MCU to reset.
Freescale Semiconductor
IRQMOD
IRQEDG
IRQACK
IRQPE
IRQIE
Field
IRQF
5
4
3
2
1
0
Reset
W
R
System Reset Status Register (SRS)
Interrupt Request (IRQ) Edge Select — This read/write control bit is used to select the polarity of edges or
levels on the IRQ pin that cause IRQF to be set. The IRQMOD control bit determines whether the IRQ pin is
sensitive to both edges and levels or only edges. When the IRQ pin is enabled as the IRQ input and is configured
to detect rising edges, the optional pullup resistor is reconfigured as an optional pulldown resistor.
0 IRQ is falling edge or falling edge/low-level sensitive.
1 IRQ is rising edge or rising edge/high-level sensitive.
IRQ Pin Enable — This read/write control bit enables the IRQ pin function. When this bit is set the IRQ pin can
be used as an interrupt request. Also, when this bit is set, either an internal pull-up or an internal pull-down
resistor is enabled depending on the state of the IRQMOD bit.
0 IRQ pin function is disabled.
1 IRQ pin function is enabled.
IRQ Flag — This read-only status bit indicates when an interrupt request event has occurred.
0 No IRQ request.
1 IRQ event detected.
IRQ Acknowledge — This write-only bit is used to acknowledge interrupt request events (write 1 to clear IRQF).
Writing 0 has no meaning or effect. Reads always return 0. If edge-and-level detection is selected
(IRQMOD = 1), IRQF cannot be cleared while the IRQ pin remains at its asserted level.
IRQ Interrupt Enable — This read/write control bit determines whether IRQ events generate a hardware
interrupt request.
0 Hardware interrupt requests from IRQF disabled (use polling).
1 Hardware interrupt requested whenever IRQF = 1.
IRQ Detection Mode — This read/write control bit selects either edge-only detection or edge-and-level
detection. The IRQEDG control bit determines the polarity of edges and levels that are detected as interrupt
request events. See
0 IRQ event on falling edges or rising edges only.
1 IRQ event on falling edges and low levels or on rising edges and high levels.
0
0
7
Figure 5-2. Interrupt Request Status and Control Register (IRQSC)
= Unimplemented or Reserved
6
0
0
Section 5.5.2.2, “Edge and Level
MC9S08RC/RD/RE/RG Data Sheet, Rev. 1.11
Table 5-2. IRQSC Field Descriptions
IRQEDG
0
5
IRQPE
4
0
Description
Sensitivity,”
IRQF
0
3
for more details.
Resets, Interrupts, and System Configuration
IRQACK
2
0
0
IRQIE
0
1
IRQMOD
0
0
65